Well the problem wasn't a problem at all. The DHL site is very confusing since they use your street number and name and the city and state their CLOSEST HUB is. I'm getting divorced and I rotate in and out of the house so I wasn't home. I just went by what I read on the DHL tracking site. I have to say
SizeGenetics was very quick to respond to my inquiry.
Now to a comparison:
I had the Fast Size for a while and didn't like the noose setup. I tried going to their site and they are temporarily shut down while they go for a medical rating they need (or something like that). So I decided to buy the
SizeGenetics due to the comfort strap.
The
SizeGenetics comes in a nice box with a spot for each part. The FastSize (FS) comes with a blue travel bag of good quality. I like the blue travel bag because I can keep the rods on the unit and carry it around with me not having to disassemble the entire unit to put back like you do with the
SizeGenetics. (
SizeGenetics - Penis Traction Extender from here on out).
Quality - the FS has thicker
extender rods and their threaded rods are thicker. The FS
extender rods have a tendency to unscrew from each other when you make adjustments using the screws - I read where some people just throw a piece of tape on them. The FS uses a single action spin where there is one threaded rod and you adjust straight up or down. The
SG has opposing threaded bars so when you adjust it you have an increase in length from the base threaded rod and also from the threaded rod going through the
extender rods. Personally I would have liked if
SG had used thicker threaded rods and I find the double action to be somewhat a pain because the
extender rods have a tendency to spin during adjustment causing an unequal amount of travel on the two opposing rods. As far as the difference in size of the
extender rods I think they are both sturdy enough.
The
SG and FS
extender rods are interchangeable since their threads are the same. So now I can grow my dick to 18" and still have enough rods left over...lol
I checked to see if the comfort strap setup can be inserted onto the FS
extender rods. Since the
SG extender rods smaller diameter the comfort strap designed front piece will not fit over the FS
extender rods. But you could just use the FS
extender rods as the last piece on the
SG and use the comfort strap front piece.
I can see how the rubber straps are breaking. There is quite a bit of tension on them when you extend to 1200 grams or more, but I think the problem comes when pulling them tight or pulling them looser through the slots. It take a good force to pull them through and the rubber stretches quite a bit. I have been careful when adjusting the rubber in or out and I make sure to grab it as close to the plastic as possible and work it out with some movement rather than just a straight pull. There are 'wings' on the straps which I think are there to help facilitate gripping the strap when loosening it.
My head still got purple and turned numb but that was after about 45 minutes of use at around 1200 grams tension. I could only get about 20 minutes when I used the noose design at a decent tension.
One other observation - the distance across the holes on the front piece on the
SG seems to be less than the distance between the bars at the base. This causes a slight inward angle of the
extender rods from the base to the tip. I don't think it's a problem since there is some slack in the unit and it doesn't appear as if the angle will cause any bending of the threaded rods. I have no doubt the FS threaded rods would hold up since they are thicker and sturdier.
One other thing. My rubber strap has a defect on the bottoms side as if it was cause by the mold it was made in. It looks like a scratch/gouge in the rubber but just outside the gouge there is some 'bubbling' that looks like extra rubber that was in the mold.
I'm going to take a picture and post it to see if
SG will replace the strap for me. It's not broken but I think this will be a weak spot and with people reporting the rubber snapping I'm afraid it won't last as long as it should.
"Click" the link, to buy at MoS Shop.