How to Measure...A Quick Guide

If you measure, is it allowed to push your dick down so that its parallel to the floor? Its bigger that way than measuring without pushing in the natural erection-angle...
 
kwyckemynd00 said:
So those people I've seen posting pic with their measurements BP'd on either side of the shaft, rather than the top, are measuring BPL incorrectly?
Click to expand...


Quite a unique name, you must be the same guy from AM. :)
 
Yep, that's me.....what's goin on bud? :D

I've better get active here....I mean, bodybuilding shouldn't skip that little area between abs and thighs, right ;)
 
In some of those instructions in dld's first post of this thread it tells you to measure along the top of your dick, but others say at the side. Clarification?
 
fredski49 said:
In some of those instructions in dld's first post of this thread it tells you to measure along the top of your dick, but others say at the side. Clarification?
Click to expand...

The top would be best because you can then rest the ruler on your pubic bone to get a good bonepressed measurement. If you do it from the side there's nothing to stop your ruler from going back farther each time you measure.

-ItsElectric
 
I am the same way...cant be 100% all the time...my suggestions are that you don't masterbate for a day or two before you measure, and when you measure kegel as much blood as you can. Taking your erect rod, grab it from the botton side with your palm facing you. Make sure you straighten it out if it is curved. This will force you to squeeze it a little which will make it harder....I hope can picture that...
 
I'm new to this forum but not new to measuring. The best instrument to measure with would be a tailors tape. Yeah its four foot long and a bitch to keep curled up BUT because its as flexible as a a peice of cloth you can follow curves in your memeber.
 
The question is
How did they measure at , for example , The Kinsley research to get the worlds average
I mean , if they did not press to the bone , then you can not compare
 
JohnnyBravos said:
The question is
How did they measure at , for example , The Kinsley research to get the worlds average
I mean , if they did not press to the bone , then you can not compare
Click to expand...
same as we here, measurment are done in closed room, but before 'subject' enters they give them instructions how to measure..
 
Day one, of the mission goal of bone pressed erect length (6 inches):)
My Day one stats are.
BPenis EnlargementL: 5 inches
BPFS: 4 3/4 inch
NBPenis EnlargementL: 4 inches
Flaccid length: 2.5 inches
Penis Erect Circumference: 4 1/2 inches
Penis Flaccid circumference: 3 3/4 inches

Wish me luck.
 
Hi, first time poster here!

I just some of my measurements:
BPenis EnlargementL = 5.25 (but that's with a plastic ruler, guessing once I get a tape measure it'd be like, 5.50

BPFS = 4.25

It doesn't change much, what does that mean?

And I couldn't measure my girth, my corona is the widest part of my penis, do I measure that or only the widest part along the shaft? Does anybody else have it like me? :/
 
I would measure the most widest part of your cock, for me its the mid-shaft area, and make sure that you always measure the same area of reference in the future to keep with accuracy.
 
April 18th 2008 new growth stats.
BPenis EnlargementL: 5 1/2 inch
BPFS: 5 1/4 inch
NBPenis EnlargementL: 4 1/4 inch
[words=http://fleshlight.sjv.io/c/348327/302851/4702]FL[/words]: 3 1/4 inch
Penis EnlargementCircumference: 4 1/2 same as last month.
PFCircumference: 4 3/4 same as last month.

P.s. wish me luck in May, thanks to DLD and the whole forum crew.
 
You must log in or register to reply here.
Back
Top