Penimastrer pro + blood

Hi,

I just received the penimaster pro, and for the life of me i don't know how to vacuum the glans in.

I got a 4 part setup for the glans part. the chamber, a diaphragm on the chamber, a second very tight latex ring with two widening plastic things inside, and the vacuum pump that normally attaches to the glans chamber.

First, i don't think i can stick my glans in that chamber with the tight thing at the end with the two plastic mold things.

Second, i tried the vacuum connection on the chamber but it's a hit and miss thing. I don't know what i'm doing wrong, but i can't get a vacuum going.

How do you do this?

Any help greatly appreciated

1st make sure you have everything hooked up right

2nd you may or may not need those rings that are half and half that will make a difference I didnt need them

3rd make sure the valve is closed if its facing you turn it all the way towards your right and it should be touching the base then squeeze the pump ball and and line it up u should see these 2 lines at the bottom of the pump ball and line it up and push it down then turn it towards the left and let it suck in the glads and ones its in turn back to the right and pull it off then u should be good

Practice using (bulb or hose) and seeing the diaphragm sucked into the chamber, without putting your glans in. After you perfect working that aspect, then proceed with having the suction draw in a lubricated penis head.
The learning curve is steep, but once you figure out the opening/closing of the chamber to hold/release the vacuum, your on you way.

Hi again,

Thanks for the explanation. I can get to the point of having the diaphragm being sucked into the chamber but not entirely, and somehow if i try turning the valve around the air just comes out.

So here's what i understood:
1- turn the valve to closed position with the vacuum pump.
2-suck the air out of the vacuum then turn, or rotate it to the left, push it towards the chamber and release the vacuum which will suck in the diaphragm.
3-pull out the pump and rotate it back to the right then take it off??

will try again now.

no you have it backwards that may be why it isnt fitting ok here we try this again visualize that the chamber is bout to be placed on your dick having it straight out in front of you ok ready

1. Make sure the valve is turn all the way to the right meaning its closed and no air can get in or out.\

2. Squeeze the pump and hold it then place it on the valve.

this is what may have confused you depending on what hand you are im right handed so I turn it towards my left to allow it to suck in what you can do is while it is sucking in assist your penis by slightly pushing it in as well and once you get it in turn it back towards your right hand.

3. If you feel you need to be sucked in more repeat step 2 by squeezing the ball and turn towards the left meaning your left arm and let is suck in till you feel its enough and turn back towards your right arm to close it off when you have enough suction hope this helps

Took me a few mins to get the hang of it as well now I can get it on in about 3 second

note to sevenup,
Don't feel like you are the only one that struggles with this issue & the PMP Pro ! I got so fed up with all the twisting squeezing of the bulb, I adapted my chamber so I can get the vacuum by attaching my Penis Pump via a quick disconnect (Cole Parmer fitting).

Ok, I don't know if this is possible.

When i have the chamber in front of me as if i were going to wear it, and the vacuum pump opposite, here is what i get:
1-the valve on the chamber is completely closed. When it is, there are these two stripes or groves in the valve, 90 degrees from the two pins sticking out at the bottom of the valvle connecting the chamber.
2-i push down the vacuum pump but not until it locks with the pins otherwise i can't turn the valve. Am i correct thus far?
3-i turn the vacuum pump until the valve opens and i can stick the pump back down to the level of the pins.
4- knowing the pump is already squeezed, i release, and well the diaphragm sucks into the chamber.

This is where i can't do anything. i move the vacuum pump the slightest bit and all the bacuum goes away. No matter what i do. So i can't understand how you can close the valve back because you have to push the vacuum pump down in order for a vacuum to take place, and pull it back out to close the valvle. This is seriously pissing me off cuz it makes me think i'm a total moron and missing something essential yet simple.

Hi again.

I have another problem here. There is no way in hell i can use that psruce. The biggest one can't allow my glans to pass through even if i was in freezing temperature. The default spruce is the biggest there is in the setup.

And i still can't do any sustainable vacuuming unless i keep the pump attached, and even then things are really fragile. The slightest rotation or push of the pump and all the air comes back into the chamber.

So far, this expensive piece of hardware is justfrankenstein looking weight.

what I mean by closing is that you need to turn it to the right that closes it

you need to start with the valve closed and then put the pump on then turn towards the left and allow it to suck in until desired pressure then when finished turned back the other was and pull it off the only thing I can think of is its not closed when u start off in the first place that is what u need to make sure if not the air will keep coming out when u pull it off