Status
Not open for further replies.

BigMiller

0
Registered
Joined
Oct 29, 2004
Messages
83
I know this idea is not new, but I thought I'ld share my device with you :)

I bought a jar lifter at eBay.com (I'm from Germany and I didn't find those here, at least not with those rollers)

Then I bought an pipe isolation made of foam, put some doublesided adhesive tape around each roll, cut the isolation and put the rolls in that.

There you go, a selfmade jelq device for under 15 Euros :) !
I have some pictures attached.

Bathmate
 
BigMiller said:
I know this idea is not new, but I thought I'ld share my device with you :)

I bought a jar lifter at eBay.com (I'm from Germany and I didn't find those here, at least not with those rollers)

Then I bought an pipe isolation made of foam, put some doublesided adhesive tape around each roll, cut the isolation and put the rolls in that.

There you go, a selfmade jelq device for under 15 Euros :) !
I have some pictures attached.

Bathmate



Looks nice to me! I wish I still had my jar lifter, I found one in Kansas City about 2 years ago, I did not like how thin the rollers were, but wiht the pipe insulation on it it looks good to go! Good luck with it man!
 
Well done, looks just like mine too. How do you like it?
 
I made it just a few minutes ago - and cannot compare it to the original.
Someone at the TP forum made it and I ordered some jar lifters (payed with Paypal).

I tested it for the first time - a little bit strange but I think it will be better after
a few tries. There's high pressure build up - but I cannot go over the full length.
Maybe when I use some lubricant - but dry... no way.

Do those of you who own an original jelq device always use lubricant?
And do those rolls actually roll over your penis or not? I read that they
don't and I should see the device as an replacement for dry jelqs...

Mine don't roll - I could make them rolling, but wanted to know what you
say about that.

Bathmate
 
The trick is to use the smallest amount of lube,too much and the rollers slip all over the place,rub a tiny bit of vasaline on the rollers then wipe off with a tissue,mine don't roll they lock up.Try doing a kegal before each rep.
 
I don't have those pictures here anymore. WIll take 2 weeks until I am home again... sorry.
 
BigMiller said:
I don't have those pictures here anymore. WIll take 2 weeks until I am home again... sorry.
That cool... Take your time... I picture it in my head what look like and I got it now....
Thanks
 
I found them in the german forum and uploaded them again.
The links do work again...
 
Wet... I use a little bit of vaseline, not as much as with manual jelqing.
I have tried to use it dry, but that didn't work. The rolls of the jar lifter are fixed so there needs to be a little lubricant.
 
I have the new offical power-jelq with the DURA-Rollers. Your homemade jeq device is very good, but the only thing that your jelq device lacks are the new rollers. These thnigs are tha bomb. The old rollers would wear out and have to be replaced. The new rollers will never wear out. These things are like that tough, pliable foam used for wrestling mats. Check them out at www.power-jelq.com The only thing you will ever have to replace is the jar lifter, which can be $3-6. Good going with your homemade version BIGMILLER. Get the hang of it and than you probrably should look into the new rollers. They make the device work even better. The sessions with mine are crazy. The new rollers allow you to stretch your penis even better now because the the new rollers get a very good grip on the penis. The old ones are good, but like I said before the new ones are tha BOMB!!! HOLLA BACK!!
 
Status
Not open for further replies.
Back
Top Bottom