forced to upgrade? (warning: graphic details)

acromegaly · Jun 15, 2018

So i finally cracked this x40 extreme and went to go grab my other x40 that i had stashed for just such an emergency, and i noticed that it had somehow cracked as well... I have been completely packing the tube girthwise every day for a while now and i thought that i could gain some length in the process of cementing girth gains. Well, even though i use a lot of coconut oil and shave properly and do everything right i have been suffering from bleeding at the urethra on and off for a while. it is, as DLD has said before, from when the head of your dick gets roughed up. i cant really stop it from happening and i think i need to get a bigger tube anyways. Unfortunately they are very expensive... i guess i am just going to bite the bullet and buy the x50 extreme, but if it is too big i will be in trouble because i will have to buy another x40...

acromegaly · Jun 15, 2018

ok, i just bought the x50 extreme with express shipping. hopefully this is good.

huge-girth · Jun 15, 2018

I'm curious to know what could be the cause of the bleeding

acromegaly · Jun 15, 2018

huge-girth;761544 said:
I'm curious to know what could be the cause of the bleeding

When the dick head gets smashed along the ridge of the tube I’m pretty sure while I start to pump. It causes no pain but it must be causing a small cut or Knick. Also it looks fucking scary obviously

huge-girth · Jun 15, 2018

Now i understand. With the new X50 extreme, you are on your way to 8 inches girth.

acromegaly · Jun 15, 2018

huge-girth;761549 said:
Now i understand. With the new X50 extreme, you are on your way to 8 inches girth.

I hope so.
I just called every sex store in my city, the biggest diameter tube they sell is 2.5 inches. Wtf

huge-girth · Jun 15, 2018

Get yourself a single mother. They have the big pussy you seek.

cladre60 · Jun 15, 2018

huge-girth;761549 said:
Now i understand. With the new X50 extreme, you are on your way to 8 inches girth.

Is that even usable?!

acromegaly · Jun 15, 2018

super depressed right now, i guess pumping was the only thing keeping me sane... the only pumps i have left are a duct taped 2.75 and the long johnny. i will try to figure something out, waiting for the x50 is going to be grueling. yes i know i sound like i have mental problems.

cladre60 · Jun 15, 2018

acromegaly;761562 said:
super depressed right now, i guess pumping was the only thing keeping me sane... the only pumps i have left are a duct taped 2.75 and the long johnny. i will try to figure something out, waiting for the x50 is going to be grueling. yes i know i sound like i have mental problems.

How bad are the cracks? If there aren't chunks missing then there's gotta be a sealer you can use. Maybe some 2 stage epoxy for plastic that dries hard.

Chaoskampf · Jun 15, 2018

I have the Long Jonny 12x4" and I still have the Thickwall Deluxe 10x3" which I don't use anymore (both can be used with water). Already quite a step from the Goliath diameter. I don't think anybody can pack tubes that are sized as the X50, maybe at the base but not midshaft. So once you have the X50 you should be safe forever.

huge-girth · Jun 15, 2018

cladre60;761557 said:
Is that even usable?!

Shorty mac is up to 8 inches girth. It's usable

huge-girth · Jun 15, 2018

acromegaly;761562 said:
super depressed right now, i guess pumping was the only thing keeping me sane... the only pumps i have left are a duct taped 2.75 and the long johnny. i will try to figure something out, waiting for the x50 is going to be grueling. yes i know i sound like i have mental problems.

Do you have any idea what caused the crack on both pumps?

Lookn4girth · Jun 16, 2018

acromegaly;761562 said:
super depressed right now, i guess pumping was the only thing keeping me sane... the only pumps i have left are a duct taped 2.75 and the long johnny. i will try to figure something out, waiting for the x50 is going to be grueling. yes i know i sound like i have mental problems.

No mental problem acro, this stuff is just addictive. Packing the x40 is not a bad problem to have although I can't say I know how you feel,

. The x50 should keep you for a good while

Chaoskampf · Jun 16, 2018

From left to right: Thickwall Long Jonny 12x4", Bathmate Goliath 10x2.75", Thickwall Deluxe 10x3", Utimi 8x2.5"

Big Schwanz Acht · Jun 16, 2018

it's just plastic, so depending upon where it cracked it shouldn't be too tough to repair. I know I'd miss my X40 and I only use my Goliath about 10% of the time

acromegaly · Jun 16, 2018

huge-girth;761575 said:
Do you have any idea what caused the crack on both pumps?

The valve part between the end cap and the pump cracks eventually from everyday pumping and pressure. It happens to all pumps not just bath mate

- - - Updated - - -

Chaoskampf;761633 said:
From left to right: Thickwall Long Jonny 12x4", Bathmate Goliath 10x2.75", Thickwall Deluxe 10x3", Utimi 8x2.5"

I’m doing longjonny cock only right now it’s really weird but getting the job done for now I guess

Big Schwanz Acht · Jun 16, 2018

acromegaly;761643 said:
The valve part between the end cap and the pump cracks eventually from everyday pumping and pressure. It happens to all pumps not just bath mate

so here's a 'quick-fix' to get you through the delay until your X50 arrives...remove the entire valve assembly so all you're left with is the cylinder and gaiter. Take your VacuVin cork and squeeze it in the opening, once you begin pumping, it'll seal-up due to the pressure

Chaoskampf · Jun 16, 2018

acromegaly;761643 said:
The valve part between the end cap and the pump cracks eventually from everyday pumping and pressure. It happens to all pumps not just bath mate

I’m doing longjonny cock only right now it’s really weird but getting the job done for now I guess

That sounds tough. A cylinder of this size and then pumping only shaft. I tend to believe that this causes large increase in base girth.

If I remember correctly Big Schwanz Acht asked in the past how to create a tapered shaft - by making use of oversized cylinders would be my suggestion.

Big Schwanz Acht · Jun 16, 2018

Chaoskampf;761649 said:
If I remember correctly Big Schwanz Acht asked in the past how to create a tapered shaft - by making use of oversized cylinders would be my suggestion.

not me, but I do recall someone posing that question (I have a slight baseball bat shape)

forced to upgrade? (warning: graphic details)

0

0

Moderator

0

Moderator

0

Moderator

0

0

0

0

Moderator

Moderator

0

0

@Big Schwanz Acht

0

@Big Schwanz Acht

0

@Big Schwanz Acht

Similar threads