new cylinder

I

icecam

0
hey pumpers in need of a little help. my current pump i have my base shaft cannot expand any more as it get fully squashed in the tube. but the mid and head dont.

should i get a bigger cylinder? i think my current cylinder is either a 1.5 or 1.75 was thinking of getting a 2inch one.

your opinions please thanx. ;)

edit my base is around 5.25 and midshaft is about 5 just :( i need more girth :(
 
I own a pump, and have used it periodically, but I am in no way a seasoned veteran. My advice to you is to get one of those skin calipers. You know, the things that you use to pinch fat on your belly and it tells you your body composition? Well, use it to see how WIDE you are at the widest part of your penis (base in your case). It should be somewhere around 2 inches, give or take a quarter inch or so. You want to write this measurement down, and buy a tube that is about 1/4 inch bigger than that. For instance, my mid-shaft is the fattest part of my cock, so it is 2.25" across (according to the fat caliper). A 2.5" tube is perfect for me, as my shaft barely misses pressing up against the tube when pumping. As soon as my shaft touches the tube, I order a new tube.

It's as simple as that.:cool:
 
my cylinder is 1.75 across the top. and my penis is 1.75 across when i put my penis in the pump its just about goes in at the base. is this an idication to get a bigger size tube?

maybe say a 2inch one ?
 
okay thanx goldmember got to order one now. but i dunno if i wana order through vacutech again as then i will have to pay customs again adding mor money to it :(

any advise bud?

had an awesome pump session earlier on. then i edged and came :( so later on i jerked off and came again i was just wanting to check on my girth. and end up getting excited lol.
 
well i got sucked into it :( lol i ended up ordering a 2x9 cylinder of vacutech soo gotta get cash to pay customs ffs lol.

cant wait to recieve this badboy im really enjoying pumping. and my length has in creased to 7.85 from 7.7 how fucking sweet is that.

and i have not done any length work for about 1week. no stretching hanging or anything. i just hope these keep coming especially girth. which i am targetting.

thanx for the advise goldie should have my cylinder soon will let you know how i get on in a bigger tube.
 
I have a 1 3/4" and a 2 "Kaplin tapered tube and a 2" and a 2 1/4" thick walled vacutech. I can no longer fit in the 1 3/4 tube. I start with the 2" tapered and spend about 30 minutes to one hour then move up to the 2" thick walled after packing out the smaller one. In about 15 more minutes I pack the lower half of the 2" thick walled. I seldom use my 2 1/4 tube. It sucks in too much of the scrotum.

All the best

lee825
 
welli have brought my pump back out to the light and have been pumping around 3-6times a week for 3x10minute sessions.

my routine today was

10mins pumping 5-7hg
5mins clamping
10mins pumping 5-7hg
5mins clamping
8mins pumping 6-10hg

light clamp for 20mins , tooks some vitamins to help heal the penis. then im gonna jelq, clamp and edge later :D

going well looking girth and flacid gains now
 
How have your gains been with clamping inbetween breaks? I usually do 60 mins of clamping + 500 slow jelqs + 60 mins of pumping(and I study/read books while pumping).

I have done clamping while resting for pumping, however, I get more girth out of getting 60 mins of clamping done before I pump, then the pump takes my inflated, clamped girth and blows it up even more for another 60 minutes(10 x 6 sets, usually).

How long does your pump last?
 
ive only recently combined both together. the last week and went well. stayed hard and was easy to get 100% through it all. took all in around 1hr to complete including breaks and regaining a stiffy.

my main aim is girth i really want a fat ass dick.

just finished another 10min clamp session and 20mins wet jelq in the bath. gonna dry jelq for a bit before bed.
 
You must log in or register to reply here.
Back
Top