Ive been waiting to post this for some time, partly due to the fact that I want to see if it would hold and not fall off and then I lost my digital cam(still havent found that bastard). This pic is taken with my phone, so Im hoping the quality is good enough.
Most [words=http://www.phallosan.com/shop/catalog/default.php?z=eNortjIxtVKyL0pNszWxMFcrSSxKTy2JL0hMT7U1UisoykyxtbBQSy4tLsnPjS8uKcrMS7dVsgZcMMpbEbo%2C]ADS[/words] devices go on the principle of holding by constriction or compression to hold on. As we all know this can cut off the circulation and cause comfort issues. I took a different method of holding on, I thought if I could use friction it would be alot more comfortable and not cause issues.
Parts you will need and websites to get them.
Cock sleeve, I used the colt stroker $16
http://www.babeland.com/page/TIB/CTGY/men-sleeves
Can also be used for wrap under a cable clamp, works beautifully. Ive tried many wraps and this one buy far worked the best, especially for comfort. Cut off a section a little over one inch long, cut off the knobs and strap it on, then throw on the cable clamp.
Shaft collar from www.mcmaster.com $15 Weighs about 2 lbs
Before buying one of these you need to figure out what your flaccid girth is and then convert that to a diameter in order to purchase the correct size. To do this just measure your flaccid girth(mine is between 5 and 5.25) then measure that out on a piece of paper, then roll up the paper and measure from edge to edge. This will give you the inner diameter for the shaft collar. I bought mine as close to that size as I could, going slightly over vs slightly smaller. If you screw this part up and order the wrong size it is easier to fix it if you buy the shaft collar slightly larger than slightly smaller.
Here is what I did, I took the colt sleeve and cut it into sections .5-1 inch longer than the width of the shaft collar. I cut off the knobs and the colt sleeve, but you dont want to do that just in case you need extra holding support because of inaccurate sizing of the shaft collar. Then put this section of the colt sleeve on the middle of your cock and then put the shaft collar on it.
Nothing slips, Ive never had it come off. Circulation is ALWAYS good. I can pee with it on. You can wear it almost anywhere if your activity level is on the low end. I dont wear underwear with it and wear khakis and you cant tell Im wearing it.
You can also wear two and this gives you a real good pull. Almost 5 lbs pulling all day is pretty good weight. I havent ventured out wearing two just yet. I usually do this around the house. It stays just fine but it makes me nervous if I were to go out with both on.
PS This is the first pic of me.
Most [words=http://www.phallosan.com/shop/catalog/default.php?z=eNortjIxtVKyL0pNszWxMFcrSSxKTy2JL0hMT7U1UisoykyxtbBQSy4tLsnPjS8uKcrMS7dVsgZcMMpbEbo%2C]ADS[/words] devices go on the principle of holding by constriction or compression to hold on. As we all know this can cut off the circulation and cause comfort issues. I took a different method of holding on, I thought if I could use friction it would be alot more comfortable and not cause issues.
Parts you will need and websites to get them.
Cock sleeve, I used the colt stroker $16
http://www.babeland.com/page/TIB/CTGY/men-sleeves
Can also be used for wrap under a cable clamp, works beautifully. Ive tried many wraps and this one buy far worked the best, especially for comfort. Cut off a section a little over one inch long, cut off the knobs and strap it on, then throw on the cable clamp.
Shaft collar from www.mcmaster.com $15 Weighs about 2 lbs
Before buying one of these you need to figure out what your flaccid girth is and then convert that to a diameter in order to purchase the correct size. To do this just measure your flaccid girth(mine is between 5 and 5.25) then measure that out on a piece of paper, then roll up the paper and measure from edge to edge. This will give you the inner diameter for the shaft collar. I bought mine as close to that size as I could, going slightly over vs slightly smaller. If you screw this part up and order the wrong size it is easier to fix it if you buy the shaft collar slightly larger than slightly smaller.
Here is what I did, I took the colt sleeve and cut it into sections .5-1 inch longer than the width of the shaft collar. I cut off the knobs and the colt sleeve, but you dont want to do that just in case you need extra holding support because of inaccurate sizing of the shaft collar. Then put this section of the colt sleeve on the middle of your cock and then put the shaft collar on it.
Nothing slips, Ive never had it come off. Circulation is ALWAYS good. I can pee with it on. You can wear it almost anywhere if your activity level is on the low end. I dont wear underwear with it and wear khakis and you cant tell Im wearing it.
You can also wear two and this gives you a real good pull. Almost 5 lbs pulling all day is pretty good weight. I havent ventured out wearing two just yet. I usually do this around the house. It stays just fine but it makes me nervous if I were to go out with both on.
PS This is the first pic of me.
if there was,where did it go?