extender setup

L

little fella

0
Hi all I have been noticing alot of questions on how to put together the [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] and also how the tension settings work so I have put together this little info thread with pictures. Ok so you receive your [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] most come in a box like this
View attachment 19463
 
Ok so now what you really want to do is make sure that you have all the pieces there that are needed. See the picture for the basic layout of what you should have received to be able to use your [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words].
View attachment 19464
 
Once again the last post did not work. So try again.
Ok now the part where most people seem to be getting a little confused and to some this may seem simple but to others it can be a reall pain.

Put the spring in place as shown.

View attachment 19473
 
Now for adding the bars there is a adaptation period so this is what it says to do in the manual anyway.

1st to 5th day 2cm under erect size use for 3 hours a day

6th to 10th day add on a 0.5cm bar use for 6 hours a day

11th to 15th day add another 0.5cm bar. use for 8 hours a day.

After doing this add the bars so it is the same length as you penis therefor you are stretching to the length of your erct penis and do this until you can add another bar you really want to be aiming to be stretching 1 inch over your erect length.

Here is a picture of the [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] with the bars on.

View attachment 19477
 
Next thing is how to adjust the tension and how you know what tension you are set at. Well the screw at the base of the rods allows you to adjust the tension by moving the rods up and down and therefore compressing and decompressing the spring. The lines on the rods allow you to see what tension the springs are giving there are three lines and I think that the best way to explain what each one of these lines represent is through a picture.

View attachment 19481
 
So to put it quite simply the more lines that you can see the less the pressure is being placed on the penis.

So I hope that this helps some in understanding a little more about the [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] how to put it together but the most important is the tension do not rush it I made the silly mistake of going all the way up on the tension setting. I did not do any injurys to myself thank god but I did get a lot of skin irritation and therefore had to take time of to heel and this hindered my gains.
 
good thread little fella...my [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] came already put together..but i still have problem with the tension...when i turn the knob to adjust the tension...the rods does not move but i end up unscrewing the rod from the base...not sure why that happens
 
twins172_up;305350 said:
good thread little fella...my [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] came already put together..but i still have problem with the tension...when i turn the knob to adjust the tension...the rods does not move but i end up unscrewing the rod from the base...not sure why that happens
Click to expand...

I really think that there is a friction problem here where the springs are place some oil in where the springs are I prefer to use bearing lubricant that comes in a tube and it is not as messy this will free that area up so when you rotate the the rods that part will move instead of the screws in the base. Or the other way that you can do it is get some light grade lock tight and place a small amount on the screw that goes into the base this will stop it from unscrewing I hope that this helps.

If this does not help please let me know and I will post pictures of these to better describe what I am talking about.
 
You must log in or register to reply here.
Back
Top