- Joined
- Jul 20, 2014
- Messages
- 1,130
Question about Bathmate x30
- Thread starter Perestroyka
- Start date
-
- Tags
- 8 inch base girth bath mate bath-mate bathmate bathmate goliath bathmate herc bathmate hercules bathmate hydromax edging gaining girth hydro max hydro-max hydromax hydromax extreme hydromax x20 hydromax x30 hydromax x30 xtreme hydromax x40 hydromax x50 hydromax xtreme inches penis question thick x20 x30 x40 x50 xtreme xtreme
- Joined
- Jul 14, 2009
- Messages
- 7,524
- Joined
- Jul 20, 2014
- Messages
- 1,130
for maximum 7 inches long and 6.5 thick, I wouldn't be able to fit it in when I reach 8 inches?
- Joined
- Jul 14, 2009
- Messages
- 7,524
Perestroyka;630246 said:
take a look at this thread i made: http://www.mattersofsize.com/forum/...-what-size-can-the-bathmates-really-take.html
with the x30, you will likely get gains up to around 8 inch bone pressed, and 5.7 inch girth at the thickest point.
if 5.3 is the thickest part for you, then you can use the x30 till you gain some girth and length, and then upgrade to the x40 once youve reached one of the numbers above
- Joined
- Jul 20, 2014
- Messages
- 1,130
Perestroyka;630363 said:
theres not really any risk in it, just potential less than ideal suction with a tube too big.
it comes down to how much money you have. if you can afford to buy an x30, then in a couple of months buy an x40, it would be worth it as you will likely make gains quicker. however, if you are a bit low on cash, juts go for the x40. your girth isnt too far off the max you can get to in it, so if you take things slowly and use it properly it should be fine
- Joined
- Jul 20, 2014
- Messages
- 1,130
You gave me all infos I need, thanks again jordey.
Perestroyka;630367 said:
no worries! just for a little more help, using my own experience, i had to stop using the hercules (which is the same size as the x30) because of the pain of pinching me at the base (my base was around 5.6 when this was happening). i was around 7.6 inches bone pressed and had about half an inch left in the tube. so, i started using the x40 witha length of 7.6 (bone pressed) and a girth of 5.6 at the base, 5.3 at midshaft, and i have had no problems and am starting to really fill the tube now that ive had some time to get used to it. the measurements you listed, are they bone pressed and base girth?
- Joined
- Jul 20, 2014
- Messages
- 1,130
Base girth is around 14 cm, depends on EQ, and the length is non-bone pressed.
- Joined
- Jul 20, 2014
- Messages
- 1,130
I will measure tonight during edging session, and I'll tell you, I am not sure about current measurments because there is a possibility that I'm wrong measure last
time. I'll do it tonight again, maybe I am dropped in size in both ways length - girth.
time. I'll do it tonight again, maybe I am dropped in size in both ways length - girth.
- Joined
- Jul 20, 2014
- Messages
- 1,130
jordey;630388 said:
Damn, I am so sad now! What happened is my bone pressed erect length DROPPED to 6.25 inches man
Girth at thickest point is 13.2 cm which is 5.15 inches.
Perestroyka;630390 said:Damn, I am so sad now! What happened is my bone pressed erect length DROPPED to 6.25 inches man
Girth at thickest point is 13.2 cm which is 5.15 inches.
what happened?? maybe you just measured wrong the first time? consistency and accuracy is key in determining whether you are gaining or not.
in light of that i would recommend you going with the x30, as you will get roughly 0.5 inch in girth gain and 1.75 inch length with it before you need to upgrade
- Joined
- Jul 20, 2014
- Messages
- 1,130
I started with an x40 and switch to a x30 and getting ready to go back to the x40 in the span of maybe 4 months? My starting stats where 7x5 roughly and can Max out of the length with the pump mod pulling my cock to about 8.5 in length. I switched because I felt more expansion in the smaller x30'. If I would have found about the wine pump mod earlier I might stayed with the x40.
Similar threads
