The Spring Ring - Possible New PE Device in the works

S

Spektrum

1
Registered
Joined
Aug 23, 2003
Messages
610
Just kicking this idea around, wanted to get some feedback before I went any further.

I was thinking about an automatic constrictor/uli/jelq machine and came up with a neat idea. The device would work by pushing blood flow constantly forward, basically like doing an infinite jelq. The rings at either end are not incredibly tight, allowing blow flow both in and out. The "spring ring" however is tight, imagine a bunch of mini-constrictors constantly moving up the penis. The video should give you an idea of what I'm talking about.
 

Attachments

  • springringsmall.zip
    212.5 KB · Views: 0
Forgot to mention, you should set this video on repeat, it's only 3 seconds long so you probably won't get the jist of whats going on unless you play it over and over, or have it on repeat.
 
that sounds like an awesome idea... so what, you would twist this thing manually? I can totally imagine how that would feel!
 
I was thinking it could be powered with a motor, that way it would be consistant and would make life much easier.
 
Hydromaxmmm. The thing is with my Penis Enlargement - I like to have control. So I can feel exactly what is going on at all times.... that's why I've never endeavoured into pumping or hanging, you dont have as much control. If it was motorised I think you should also make it usable without the motor: i.e. just for manual 'screwing' :)
 
What would the material for the device be made out of is the question... it seems like a solid idea.
 
TimBo755 said:
What would the material for the device be made out of is the question... it seems like a solid idea.
Click to expand...

That's what I'm trying to figure out.

It would need to be some sort of hard rubber that holds it's spring shape, yet can be stretched enough to be able to put the penis in.

Still working on the details :)
 
I'd suggest that the rubber, or whatever material you end up using, needs to be impervious to oil.

Why does the material need to be hard? As I'm seeing it in my head, it'd need to be elastic (the inner coils moreso than the outer) so that it hugs the shaft.

Lastly, would there be some kind of crank that would be turned, either by motor or hand, that rotates the device?
 
Forgot to ask if there could be a way to use the spring ring in conjunction with a clamp.
 
the materials would have to be relatively solid, otherwise it would contract on its self - making the gaps in between the spring smaller. it looks to me that the whole device would have to be solid, (a little flex would be needed on the end rings to get the glans in) and the spring would have to be made to fit out of a solid material. im thinking metal would be fine because of the physical properties of a spring (if you push the 2 ends together the whole thing would dilate - allowing access). of course with a device like this friction would definitly be a problem
 
penguinsfan said:
I don't have winzip. Is the non-compressed version to large to post here?
Click to expand...

Download ExtractNow ... its FREE, search Google it supports many formats.
 
Good idea, but With this what would happen if you started to loose erection and went flaccid? Could anyone maintain a good erection with that spinning on their penis? Hey, I aint knocking it ... if it can be pulled off than I think it would kick ass. If you ever want someone to test it than I will test it for you, haveing extensive experience in jelqing and clamping I would have a very good idea of what to look for and you would get some honest critisism and feedback.
 
Red: I actually think it would be a great idea to combine it with clamping/constricting. If I do build a few, I'll be sure to send you one for testing.

Evo: I was considering a latex dipped mild steel spring to be used for it. The problem with a steel spring is the shape will not conform to give the penis a uniform pressure. That and there would have to be an incredible amount of sizes. Basically the problem here is finding a material that will hold it's shape lengthwise, but can conform it's diameter to the penis's non-round shape.
 
going4nine said:
I'd suggest that the rubber, or whatever material you end up using, needs to be impervious to oil.

Why does the material need to be hard? As I'm seeing it in my head, it'd need to be elastic (the inner coils moreso than the outer) so that it hugs the shaft.

Lastly, would there be some kind of crank that would be turned, either by motor or hand, that rotates the device?
Click to expand...

The material will need to be a bit solid to hold it's length and keep the length inbetween the springs slightly uniform.

You're right about the hugging of the shaft. And as far as being motor or hand driven, I'll come up with a way where it can be either. Twisting by hand would be much safer to start with, but would become tiresome. A motor would make the job easy and consistent.
 
hHydromaxmm, basically your problem is:- how can this device hug the shaft and be rigid enough to keep the gaps equidistant from each other?

solution:- have a flexible coil, (i was looking at the silicon loop you get with the extenders) or rubber. with support rods (you would prob need 3-4) running latterally, attatched to each coil. (this would not contact the penis but run on the outside of the coils)

i also think that the two main rings should stay motion less, while the coil be driven independantly (maybe a small bearing system?) the two main rings moving would yield alot of friction!! which is also a main problem point.
 
EVO said:
hHydromaxmm, basically your problem is:- how can this device hug the shaft and be rigid enough to keep the gaps equidistant from each other?

solution:- have a flexible coil, (i was looking at the silicon loop you get with the extenders) or rubber. with support rods (you would prob need 3-4) running latterally, attatched to each coil. (this would not contact the penis but run on the outside of the coils)

i also think that the two main rings should stay motion less, while the coil be driven independantly (maybe a small bearing system?) the two main rings moving would yield alot of friction!! which is also a main problem point.
Click to expand...

Great ideas!

It's hard to tell by the video, but the two main rings do stay stationairy much like you said, the springs are anchored in the rings, but rotate freely in them. I didn't think about using bearings, which is odd because I have an obsession with them in things I make around the house, lol

A flexible coil is a good idea. I know that the spring type has to be a torsional spring(much like the springs you use to hold weights on a bar or like the springs in a clothespin). Problem is, most torsional springs have no gap inbetween the coils and a search for "flexible-torsion-spring" came back with 3 results on google. I'll keep on looking.
 
why would you need a tortion spring?

if you used the "rods" idea - they would support the size of the device, both length and diameter wise. while the flexible interior did all the word.

just had a brain storm - why not use some kind of strechy cloth to create the spring?
it would be held in position by the rods,(imagine 2 rods with the cloth in between them) and would cling to the shape of the penis. plus it wouldnt be that hard to adjust it .....just adjust the length of cloth.
 
If you let RED be a tester, you'd have to take out a loan just to cover the cost of materials! lol
 
You must log in or register to reply here.

Similar threads

L
Info taken from a site called ""the small dick club""
2 3
Replies
43
Views
5K
H
huge-girth
H
B
Newbie finally boarding the train..... next stop, Longville!
2
Replies
25
Views
3K
DLD
DLD
DLD
BornInFigi
Cockrings: unexpected benefits-revisited. Looking back on a year.
2
Replies
31
Views
18K
H
huge-girth
H
DLD
Understanding How Size is Gained: Penis Enlargement Exercise, Routine and Equipment
2 3 4
Replies
72
Views
12K
DLD
DLD
DLD
P
Please i need HELP !!!!!!!!!!!!!!!!!!
2 3
Replies
56
Views
12K
DLD
DLD
DLD
Back
Top Bottom