Girth work What size pump cylinder to order? How to accurately measure your penis for pump cylinder sizing!

oldandlively said:
That's a partial truth. If there are already deformities, they will become more pronounced. As you expand and fill up the cylinder tightly, everything becomes uniform.


That applies to all. This is why pumping needs two cylinders to work with. A loose/larger cylinder for a larger expansion, while a cylinder that is slightly larger or snuggy to build uniformity.
Click to expand...
I would also say a tighter tube for length work. It is a very good method.
 
I suggest 1 and 1 is great. Are using one tube for length and the other girth?
 
DLD said:
I suggest 1 and 1 is great. Are using one tube for length and the other girth?
Click to expand...
Originally the wider pump for straightening out a small curve. Then I saw girth and length results and was using a wider pump for all three. Then the suggestion came to use both, and you suggested the thinner tube would be better at fixing flaws.

I just bought a thin 12 inch tube. I’m a newbie (apx 5 months) and I’m at a length that might max out the shorter one soon. Still taking it slow per you, @hugegirth, Old and others here.

Thanks!
 
You are welcome! I recommend 1 and 1. Maybe do 2 workouts one for length and another for girth. Go for at least 15 minutes each workout.
 
AimingStraight said:
@oldandlively to use both size cylinders; do you have opinions on a ratio? Like a 1 to 1 use. Wide one day, then narrow the next? Suggestions?
Click to expand...

As DLD indicated, 1:1 is great for curve control, or curve correction. 1:1.25 is great for girth increase, while maintaining proper curve correction and uniformity. Some brothers here have larger glans, so 1:1.5 is required.

As for the routine, I would say every day is 1:1 routine, while implement 1:1.25 or even 1:1.5 every other day to increase girth right after the 1:1 routines. If there's a strange confusion due to the codes we're using, let us know. We'll expand on the subject for greater clarity.

AimingStraight said:
Still taking it slow per you, @hugegirth, Old and others here.
Click to expand...

We're very proud of your patience on this journey. Don't go hard and heavy. Slow and steady until you reach your precondition levels before you go moderate and hard later. You'll see changes along the way. No need to rush.

By the way, any additional manual routines before the pumping?
 
  • Like
Reactions: DLD
AimingStraight said:
Yes. Usually a shower with stretching.

Jelqing and additional stretching opposite the curve after pumping.
Click to expand...
Got it. Once you hit the 6th month mark, manual jelqing and stretching is considered as warmup. Go one step further after that initial 6th month using mechanical assistant. An example is the Length Master, or even a simple broomstick, an all day stretcher (ADS), or even an extender. These devices allow you force the tissues to be broken down faster, with less work, and acting as a precursor routine to to maximize your growth and correction. Penile curvature correction does require growth first, and as growth comes, new cells fix the old curve as the penile shaft lengthen and expand girthwise. But for now, perform your stretches, and every passing week, increase on the intensity on the pull more. Every time you increase intensity, make sure there is no pain whatsoever. Just that achy dull feeling of being stretched.
 
REDZULU2003 said:
What size pump cylinder to order?


Gain Length

​
The rule of thumb is if you are focusing on penis length , order a MityVac pump cylinder in a diameter that is closest to the thickest part of your erect penis girth (see measurements below). The idea is to pack your erect penis in the cylinder and pump so your penis only extends in length since it can't expand much in girth.


Gain Length and Girth
​

Order a MityVac pump cylinder that is .25" larger in diameter than the thickest part of your erect penis girth. This will allow your penis to expand in girth and length at the same time. Ordering a pump cylinder that is much wider than the girth of your penis is not beneficial and will actually cause you to grow a deformed penis over time. So stick with the recommendations we provide, this is all data collected from pump users over the past 20 years.


How to accurately measure your penis for pump cylinder sizing
​

Get a piece of string, thread, wire, etc.

Get your penis erect.

Wrap the string around the thickest part of your ERECT shaft or base (whatever is thickest).

For most people, the thickest part of the penis is at the base of the penis by the pelvic bone. In some cases, some men have a thicker upper shaft. If this is the case, measure the thickest part of your shaft.

Mark where the string where it overlaps itself with a pen so that you can see the pen mark on both ends of the string.

Lay the string on a flat surface and measure the distance between the two pen marks with a ruler.

If your erect girth measurement is:


4” to 4.75” Order a 1.75″ diameter pump cylinder
5″ to 5.75” Order a 2″ diameter pump cylinder
6″ to 6.75” Order a 2.25” diameter pump cylinder
7″ to 7.5” Order a 2.5” diameter pump cylinder
7.75” to 8.25” Order a 2.75” diameter pump cylinder


If your measurement is not listed here – Please Contact Us

NOTE: Be sure to use string to measure circumference. A tailors tape or flexible ruler will not provide accurate measurements.

The MityVac standard cylinder length is 9.25 Inches.



Click to expand...

Wonderful, I've never seen this post before. I've been looking for a for a way to know the exact pump size for every penis size. Glad I finally found it here. I will save the post for future reference.
 
I think we need to do an update on RedZulu's instruction as the cylinders have evolved over time. Any brothers with the high knowledge of the MityVac want to tackle this on?
 
You must log in or register to reply here.
Back
Top