My Penimaster modification...much more comfy and user friendly!

[stillwantmore]

Posted this on Th*nd3rs Pl@ce first yesterday because there are several guys already using a [words=https://www.internetzahlung.de/cc-aktuell/bestellung.php3?PID=PM0440A&Sprache=en]Penimaster[/words] there. A guy that went by 'aaa' over there came up with the original idea first.


I used a 1.5" diameter "coupler" PVC. I also bought a small saw. I had nothing to cut the coupler. A couple small bolts...I ended up using the shorter one..and, a wingnut. Oh and a small pocket knife to clean up the pieces and some sandpaper.

 

[stillwantmore]

Here is a pic showing how I found the approximate center of the coupler. I made a "dotted line" with a permanent marker around the coupler. Then, I scrolled a cut all the way around it with the saw. I continued to cut along the diameter until I had cut all the way through. Cleaned it up with some rough grit sand paper.

 

[stillwantmore]

Here's what the pieces looked like after splitting them. Next step was to heat my oven to 400 farenheit and, place one piece at a time on a cookie sheet. Heat for around 45 seconds. Using an oven mit, I took the piece out and, then placed it round side up on my counter top. Used the handle of a pair of plyers to press the piece almost completely flat but left a semi curve to it. You have to hold the piece pressed down how you want it until it begins to cool. Otherwise, it will spring back.

 

[stillwantmore]

Ok, now I have fit the pieces to the 'skid' or front piece of the [words=https://www.internetzahlung.de/cc-aktuell/bestellung.php3?PID=PM0440A&Sprache=en]Penimaster[/words]. I fit them by trial and error until about 3/16" ish was protruding through the bottom of the skid. I cut small cutouts similar to what you would see on an American Indian arrow head on the side of the bottoms of the pieces pointing toward you. Also, I gave the bottoms....I guess you could call them the Tangs...a slight outward curve. This and, the fact that the pieces are fit to the slots in the skids pretty snugly keeps the pieces secure and from pulling out when you have it all together as pictured here. I did not have a drill. So, I used a lighter and heated both sides of the top of each piece where I wanted the holes. Then, I took a pair of needle nose pliers and, "drilled" the holes to the size needed for the bolt. Here it is all together and in use.

 

[stillwantmore]

Side shot one.

 

[stillwantmore]

Second side shot.

 

[DLD]

ouch...does it hurt?

 

[stillwantmore]

Nope. Just a nice light but constant stretch.

 

[DLD]

I think your penis looks the best in this piece of equipment than any I have seen. They should use you as the poster boy.

 

[stillwantmore]

Or, maybe youre just in love with my penis DLD? I'm in love with your feet!

 

[XxjustmexX]

I couldn't imagine that on my penis....how are the gains .

 

[stillwantmore]

I've only been using this a couple days now. Other guys are reporting good gains from it though. Some 1/4" a month.

 

[pUNKY]

were can i buy one from?

 

[stillwantmore]

www.penimaster.com

 

[Gardenier90]

They really are a high quality product they just need some work to be perfect.

 

[dr.ralph]

Hey guys - this is my first ever post in a Penis Enlargement forum.

Could someone please tell what the difference between the [words=https://track.moreniche.com/hit.php?w=113512&s=1220]JES[/words] [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] and the Penis master is ?

I know this subject has been discussed before - but could someone in short words describe the difference ?

I know the [words=https://track.moreniche.com/hit.php?w=113512&s=1220]JES[/words] [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extender[/words] is VERY expensive (700$) and the penis master is quite cheap - but which one works the best ?

As far as I can see, the head-strap on the [words=https://track.moreniche.com/hit.php?w=113512&s=1220]JES[/words] is made of soft gel, and the head-strap on the penis master is made of hard plastic.
What do you think will work the best way and ensure the best result ?

Thanks in advance