Is there a way?

You can probably find a one way valve at hardware store that you can use instead on it
 
That was big issue for me when it started sticking out past my hip bone. I know there are other vacuum [words=https://shop.mattersofsize.com/products/sizegenetics-penis-extender]extenders[/words] that have detachable pumps, but I wouldn't know how to rig it up
 
Supra;681944 said:
To wear the PH without the pump attached? It adds so much size to it.
Click to expand...

One member and I used a small piece of tape over the top. It seals it up pretty good. It doesn't get any vacuum but it'll hold for light duty. Works pretty good.

Other than that, use a female end one way valve from a [words=https://officialhydromaxpump.com/?uid=6&oid=2&affid=98]penis pump[/words] and screw it into the top. I've been deciding on using the small bell for this experiment since I only use the large bell. The top of them have a few small holes instead of just one. I believe putting a clear resin inside and outside the bell would close these holes and allow you to screw and tap for a one way valve. The problem is I don't know how far it'll stick inside the bell. It might hurt the glans.
 
Supra;681944 said:
To wear the PH without the pump attached? It adds so much size to it.
Click to expand...

What do you mean Supra? PH? I do not know what this is/?
 
Nice, do you know a size and are you using these already?

How can you use the pump, then disconnect it without losing pressure?

Is there a way?
 
Yeah bra its a one way valve like the one of a [words=https://officialhydromaxpump.com/?uid=6&oid=2&affid=98]bathmate[/words]. After its fitted you just need to suck the air out with your mouth, and it locks in the vacuum. I don't have a [words=http://www.phallosan.com/shop/catalog/default.php?z=eNortjIxtVKyL0pNszWxMFcrSSxKTy2JL0hMT7U1UisoykyxtbBQSy4tLsnPjS8uKcrMS7dVsgZcMMpbEbo%2C]phallosan[/words] so its up to you to go in the store, and show it to the guy so he points you the right direction
 
This one looks cool bra its called miniature check valve, and it appears you can chop both stems off, and strap the disk onto your bell then use a little hose to suck the air out
View attachment 31372
 
templnite;682174 said:
This one looks cool bra its called miniature check valve, and it appears you can chop both stems off, and strap the disk onto your bell then use a little hose to suck the air out
View attachment 31372
Click to expand...

Very innovative. A thread tutorial would be a good idea if when you make your version Supra maybe you can video it.
 
templnite;682174 said:
This one looks cool bra its called miniature check valve, and it appears you can chop both stems off, and strap the disk onto your bell then use a little hose to suck the air out
View attachment 31372
Click to expand...

I dont see how it attaches to the bell valve on the PF though.

Thanks for the pics! Hoping I get this resolved.
 
Poster putty it doesn't leave residue, and you can reuse the same glob forever
 
The problem is the PF has these two small holes at the top of the bell valve..which allows the pump to suck the air out of the bell.
 
I don't see a problem bra just bevel the check valve so it fits perfect
 
So I am the only one here who uses the pump after reaching the desired vacuum level?

Thanks Temp, I appreciate the help.
 
I use it. It has to stay on so not much else to do if you want good vacuum. I just haven't gone to a store or ordered anything. I'm just being lazy since nothing is wrong with it right now.
 
You must log in or register to reply here.
Back
Top