extender confusion

7inchesdream · Oct 10, 2017

hey guys, ive been using a extender for a month and a half, and today i was able to put the thing on past my erection length.

problem is the tension i achieved by doing this... i ve read that low tensions (below 1200g) is the way to go, but when i build the extender long enough to surpass my EL, the extender just sits in 1800g-2000g.

so, basicaly, i cannot extend past my EL without reaching higher levels of tension... is this normal and ok or should i use lower tensions? it seems impossible to extend past EL without achieving high tension..

btw: when using 1800g tension i cant only use the device for about 1,5 hour per session due to pain/burning... is this ok?

Lookn4girth · Oct 10, 2017

Which extender are you using 7?

7inchesdream · Oct 10, 2017

Lookn4girth;742195 said:
Which extender are you using 7?

my extender is almost identical to this one, but from a brazilian brand.

Lookn4girth · Oct 10, 2017

That looks just like my SG. You may have to play around with the bars to get it right where you want it. It sounds like you are using too many bars to start with and this may be why you are at the high tension. You might want to start with less bars and use the adjustment screws at the base to keep your tension at 900 to 1200. When your penis stretches and you are adjusting too far out with the screws, then you can put in another bar. I can tell you how I do mine. I start that morning with the 2 smaller bars and adjust the tension throughout the day as my penis stretches. By the end of the day I am able to replace the 2 smaller bars with one of the long bars and use the adjustment screws to maintain the tension at the middle marks. I may not be explaining it right but I hope this helps. You can also read the threads in the Sizegenetics forum here on MOS.

7inchesdream · Oct 11, 2017

Lookn4girth;742208 said:
That looks just like my SG. You may have to play around with the bars to get it right where you want it. It sounds like you are using too many bars to start with and this may be why you are at the high tension. You might want to start with less bars and use the adjustment screws at the base to keep your tension at 900 to 1200. When your penis stretches and you are adjusting too far out with the screws, then you can put in another bar. I can tell you how I do mine. I start that morning with the 2 smaller bars and adjust the tension throughout the day as my penis stretches. By the end of the day I am able to replace the 2 smaller bars with one of the long bars and use the adjustment screws to maintain the tension at the middle marks. I may not be explaining it right but I hope this helps. You can also read the threads in the Sizegenetics forum here on MOS.

i was using 2 big bars plus 1 small bar. To achieve 900g, i have to remove one of the big ones, but then my lenght on the extender becomes much smaller... like 0.5 inch smaller than my erect lenght. And i just cant fell anything! i dont fell any disconfort, strech or burning... is this correct?

can i post photos of my penis in the extender here?

thanks for u help bro

DLD · Oct 11, 2017

7inchesdream;742233 said:
i was using 2 big bars plus 1 small bar. To achieve 900g, i have to remove one of the big ones, but then my lenght on the extender becomes much smaller... like 0.5 inch smaller than my erect lenght. And i just cant fell anything! i dont fell any disconfort, strech or burning... is this correct?

can i post photos of my penis in the extender here?

thanks for u help bro

Rely on the springs as much as possible understanding there is a full .25" available there. When this is taped add .25" bars for best results.

Lookn4girth · Oct 11, 2017

7inchesdream;742233 said:
i was using 2 big bars plus 1 small bar. To achieve 900g, i have to remove one of the big ones, but then my lenght on the extender becomes much smaller... like 0.5 inch smaller than my erect lenght. And i just cant fell anything! i dont fell any disconfort, strech or burning... is this correct?

can i post photos of my penis in the extender here?

thanks for u help bro

The idea behind the extender is to keep you elongated when you are not using other tools for length such as the LM, healing extended so to speak. You want to have enough tension to keep you extended but you may not feel any burning when you are in the extender. Just as an example, I can wear my SG and adjust to keep medium tension but don't feel a burn. I can feel a pull but nothing that causes pain or discomfort. As the extender stretches you during the day, you are able to adjust to keep tension at the level you want. If you are having to adjust too much, that is when you can add another bar

huge-girth · Jan 17, 2023

7inchesdream said:
hey guys, ive been using a extender for a month and a half, and today i was able to put the thing on past my erection length.

problem is the tension i achieved by doing this... i ve read that low tensions (below 1200g) is the way to go, but when i build the extender long enough to surpass my EL, the extender just sits in 1800g-2000g.

so, basicaly, i cannot extend past my EL without reaching higher levels of tension... is this normal and ok or should i use lower tensions? it seems impossible to extend past EL without achieving high tension..

btw: when using 1800g tension i cant only use the device for about 1,5 hour per session due to pain/burning... is this ok?

If you are still having problems with your extender, get yourself a LengthMaster - Penis Bundle Stretcher & Weight Hanging. It's the best PE tool in the PE market for length right now.

DLD · Jan 17, 2023

huge-girth said:
If you are still having problems with your extender, get yourself a LengthMaster. It's the best PE tool in the PE market for length right now.

Best tool available for length

extender confusion

7inchesdream

0

Lookn4girth

0

7inchesdream

0

Lookn4girth

0

7inchesdream

0

DLD

doublelongdaddy

Lookn4girth

0

huge-girth

Moderator

DLD

doublelongdaddy

Similar threads