Did you watch the instructional video? That's what the wire clip is for on the end of the bulb. You have to pump and then put the wire clip in place. It's a safety to prevent what is happening.
Size Doctor
- Thread starter Super
- Start date
-
- Tags
- size size doctor
Did you watch the instructional video? That's what the wire clip is for on the end of the bulb. You have to pump and then put the wire clip in place. It's a safety to prevent what is happening.
Are you talking about the grey vacuum pump bulb or the sizedoctor plastic bulb? The black plastic adapter has to be attached to the grey bulb.
We are shooting a better video of close ups in the am. It will be explained in better detail.
Make a video on your phone and post it here. You can upload videos right into posts. Click the video icon in the editor next to smilies and shoot the video directly into the post.
FullBloodArab
Active member
Sometimes this happens. If I know what you mean.
Pul the fixingband off, then insert your finger inside and click the valve (the white plastic part) in place tightly from the inside. Sometimes the valve gets loose.
Then try again
FullBloodArab
Active member
Have you gotten to use yours and is it working for you? I still have not gotten to work
Last edited:
Supra, you mentioned the metal part came out of the grey pump bulb. It looks like you put it in backwards because the air is blowing in the wrong direction instead of vacuuming. Not sure why you are having all these issues but you can send it back and we will exchange it or refund you. We carefully test these one by one before they ship out and many have shipped already and there are people in the forums using them.
Thats the Spirit! I know you make it work, your Supra!
waterman8888
New member
OK guys, so I just got my Size Doctor. Tried it out today to see how it works - looks like it's going to be a sturdy bit of kit.
The valve though doesn't close for me either - so I put the black adaptor first, then grey bulb, then pump and my glans comes in - all fine till that point. Then you have to remove the grey bulb and black adaptor - when you do all the air goes out via the small black pin (the one with the orange o-ring on it) because it's in the outward position and the action of pulling the black adaptor away from the head pulls on this pin. So only way is to not take off the black adaptor but then vacuum gets lower over a few minutes. Any ideas?
I did just check the vid earlier in this thread, and it seems from seeing it that the black pin should be able to be in the loose position even after removing the pump without air escaping, and then you use the clip to keep it in place so that it doesn't go in too far, and then to release the air you push the black pin in? If so then that's the opposite of what I have where, in order to keep air in the chamber the pin has to be pushed in, and pull it outwards and it releases air....
Cheers
The valve though doesn't close for me either - so I put the black adaptor first, then grey bulb, then pump and my glans comes in - all fine till that point. Then you have to remove the grey bulb and black adaptor - when you do all the air goes out via the small black pin (the one with the orange o-ring on it) because it's in the outward position and the action of pulling the black adaptor away from the head pulls on this pin. So only way is to not take off the black adaptor but then vacuum gets lower over a few minutes. Any ideas?
I did just check the vid earlier in this thread, and it seems from seeing it that the black pin should be able to be in the loose position even after removing the pump without air escaping, and then you use the clip to keep it in place so that it doesn't go in too far, and then to release the air you push the black pin in? If so then that's the opposite of what I have where, in order to keep air in the chamber the pin has to be pushed in, and pull it outwards and it releases air....
Cheers
Last edited:
REDZULU2003
Well-known member
I wonder what that is (confused) not got one here yet, on its way to me.
Please feel free to send Lightning a PM, or/and email [email protected]
Please feel free to send Lightning a PM, or/and email [email protected]
waterman8888
New member
Thanks yes I've done that already, but thought it would be helpful to others to share my experience here too
I am still waiting for mine too and I did hear that there’s a learning curve and to be patient with myself. This is brand new to all of us so I’m sure we’re going to get better and better at using it by helping one another through our post here.
waterman8888
New member
There's only one way it can go really - black adaptor goes first onto grey bulb (side of grey bulb where there are internal ridges in the connection) then other side of the black adaptor goes onto the size doctor for pumping. In mine, it won't pump unless you first release the black pin a bit from the head (black pin with orange o-ring) so that it wobbles about a bit. You can then pump air....
Thanks for your advice my brother it is much appreciated
waterman8888
New member
Just reading on Thunders about the older Size Doctors - seems it's been the same issue before with air releasing once you remove the bulb and adaptor. From what I can see, people have said that they got it to work by waiting a few seconds, tilting the Size Doctor up and wiggling it around to get the pin to drop back first. Then release the bulb..... So seems there's a knack to it and it's not as simple as the vid suggests. Will experiment again tomorrow.
Well let’s get everything out there that we can think of and see if we can make improvements and modifications to make things better and if that’s the case we can send out modifications to everyone. But let’s keep brainstorming to see what we can find to help one another or to make modifications.
With the safety wire clip moved to side, keep the black plastic post with o-ring pushed in while you pump. Make sure the white rubber piece inside the SizeDoctor clear orange plastic bulb is pressed in (sometimes they get loose).
Attach the vacuum bulb and adapter and pump. The suction will be slow but it was intended that way. The pump bulb will squeeze fast but expand slow. Once you are secured, remove pump and put wire safety over o-ring to secure.
The black adapter creates a better seal with grey pump bulb.
Attach the vacuum bulb and adapter and pump. The suction will be slow but it was intended that way. The pump bulb will squeeze fast but expand slow. Once you are secured, remove pump and put wire safety over o-ring to secure.
The black adapter creates a better seal with grey pump bulb.
waterman8888
New member
Thanks Lightning. That's what I was starting to do but then even the suction force from the bulb pops the pin out again. I'll experiment later today again.
OK, I got the pump working, now I'm in the same place
waterman8888 is at.
waterman8888 is at.
REDZULU2003
Well-known member
It is, but doing the email can also get quicker support.
REDZULU2003
Well-known member
Yeah keep communicating ideas, because THIS is what makes us different to other companies out there, in that MoS listens to feedback, and actively improves the products.
waterman8888
New member
OK so I tried again. No way I can get it to work without a modification to the pump adaptor system - seems like a design issue to me.
The problem is still that as soon as you want to remove the black adaptor, the suction is lost as the black pin is not engaged - I have tried to half press the black pin in before starting suction, but the pin comes out in direction of the bulb as soon as you pump. I think what we need is a way that once you've pumped, you can engage the pin before the adaptor is removed - e.g. cutting the black adaptor shorter so that it can be used to suck out air, then to close the pin you press it towards the unit (it's too deep to work at the mo).
So these Size Doctors have been around for a while haven't they? Is this design so different from the previous in this regard does anyone know?
The problem is still that as soon as you want to remove the black adaptor, the suction is lost as the black pin is not engaged - I have tried to half press the black pin in before starting suction, but the pin comes out in direction of the bulb as soon as you pump. I think what we need is a way that once you've pumped, you can engage the pin before the adaptor is removed - e.g. cutting the black adaptor shorter so that it can be used to suck out air, then to close the pin you press it towards the unit (it's too deep to work at the mo).
So these Size Doctors have been around for a while haven't they? Is this design so different from the previous in this regard does anyone know?
stillwantmore
Well-known member
Seems like the Silistretcher is the better/simpler device.
Is there anyone that has found a way to use the size doctor extender successfully?
Yes indeed, It just is a very big learning curve that will get tesolved as all things do here.
Lightning has a new video coming. Stillwantmore tested the very first unit.FullBloodArab
Active member
Still no vacuum? Did you try to push inside?
Supra, did you get your vacuum straight yet?
I'm following this thread. I need users to confirm that they have succeeded in mastering how to use this device.
FullBloodArab
Active member
Also problems?
FullBloodArab
Active member
I don't now what it is then. When mine does that then it's the plastic thing inside and then I just have to push it in.
If you trying to figure it out then remove all the rods and only the bulb in your hand, then take fixingband nr1. Then suck your finger in. This way you figure it out a lot quicker and try all sort things. Like pushing the black thing or pulling on it etc. Just in your hands.
It's just a small hint because fixing it with trying your penis to suck in at same time to much work.
That way you will find out what the problem was.
Thanks for all your help my brother. This is a big learning curve for everybody so we hope everybody continues to give us feedback and other issues that are happening so we can perfect this. I’m so sorry for those who are struggling but in the end we always make it work. Have patience my brothers. If you were here long enough remember when the Bathmate came out, and remember when the Lengthmaster came out, everybody had issues to we figured it out. And today those two pieces of equipment are 2 of the biggest and best in PE.
REDZULU2003
Well-known member
Anyone who has this device from MOS please report the truth in how you find it.
Dont lie, or hold anything back. You wont be banned on here for speaking the truth.
Dont lie, or hold anything back. You wont be banned on here for speaking the truth.
No one ever would be banned for speaking truth. That will never happen here, ever. Freedom of speech and expression are most important.
The challenge I’m having is the silicap starts slipping and eventually I slip out. I put the silicap on first then the sleeve - initially I had the thick band part of the sleeve at the base of my penis but then I flipped it around - so the silicap, then the thick part of the sleeve (closer to the glans) then roll the rest of the sleeve down to the base.
Going to try different band sizes to see if it will help me stay without slipping out.
Also, for some reason my glans get really irritated when pulling out. Afraid to try it without the silisleeve/silicap (thinking it may be more painful as the tender penis head rubs against the retainer band - (if the band is too big you slip out if it’s too tight then it’s hard to get out).
As far as build quality goes it’s really well made - the base is a bit tricky being open at the bottom.
Going to try different band sizes to see if it will help me stay without slipping out.
Also, for some reason my glans get really irritated when pulling out. Afraid to try it without the silisleeve/silicap (thinking it may be more painful as the tender penis head rubs against the retainer band - (if the band is too big you slip out if it’s too tight then it’s hard to get out).
As far as build quality goes it’s really well made - the base is a bit tricky being open at the bottom.