My steps for wearing a vacuum extender (with photos)

O

onebirdtworock

0
I am still new to PE and here is how I am now wearing a vacuum extender. This is not the Stealth stretcher but a Sizegenetics modified with a vacuum bell, but the principle is the same. I hope this will be useful for people who are putting it on for the first time. But I am looking for other members to share their own methods and suggestions to make wearing an extender easier and more comfortable.

1. Clean the head of your penis and put on the silicone cap. I found it easier to put on erected and air won't be trapped. If you are uncircumcised or if you are cut but still have loose foreskin, I would suggest retracting the skin fully.

View attachment 1830408

2. Slide the extender base down the shaft to the pubic bone. Slide it in before putting on the bell because the bell has a larger diameter and you can't do it the other way around.
View attachment 1830409

3. Put on the vacuum bell on with the arrow on top. (Some bells have arrow markings to indicate the top).
View attachment 1830410

4. Roll the silicone sleeve down to the penis shaft. I use an elastic band to secure the sleeve on the bell.
View attachment 1830411

5. Use the vacuum pump to suck out some air from the bell.
View attachment 1830412

6. (Optional) Wrap with self adhering no-hurt tape for extra securement. I am using the 3M no hurt tape, which adhere to itself and is re-useable. If necessary, use the vacuum pump at this point to create the vacuum.
View attachment 1830413

7. Put the extender cap at the end of the rods
View attachment 1830414

8. Clip the bell to the cap.
View attachment 1830415

9. Adjust the tension
View attachment 1830417

10.Adjust the angle of the penis. I point it down if I am going to wear pants, or just straight out perpendicular if I am going to be sitting down.
View attachment 1830418

With this method, I have been able to wear it continuously for 3 hours or longer, with no blisters or blood restrictions to my penis. I look forward to see how other members do it.
 
I do similar for my vacuum stuff. My issue is my injury that idk how to stop. I get little blisters at the very very tip of the head, I try to squeeze all the blood out, but it's very easy for them to reoccur. And take forever to heal, otherwise vacuum is great
 
philevan said:
I do similar for my vacuum stuff. My issue is my injury that idk how to stop. I get little blisters at the very very tip of the head, I try to squeeze all the blood out, but it's very easy for them to reoccur. And take forever to heal, otherwise vacuum is great
Click to expand...

I haven't really had any issue with blisters. I put on the silicone cap over my glans and part of the shaft and make sure there are no air pockets. Also, how does the bell fit? I was using a bell with 38mm ID, but just got a smaller one (33 mm ID) and I think it might help if your glans fit somewhat snuggly inside the bell to begin with so that you are not really vaccuuming as much, therefore less swell and less chance of blistering.
 
Wolfenstein@ said:
And the silicone sleeve where did u buy it ? Did it last long for you ?
Click to expand...

The sleeve came with the kit I got from Aliexpress. It is not that durable as it had some scuff and torn pretty much the second time I used it. I cut off the torn part and had been using the remainder of it for the past three/ four weeks. It has developed some holes around the rim of the bell so I will need replacement soon. Do you have suggestions?
 
onebirdtworock said:
The sleeve came with the kit I got from Aliexpress. It is not that durable as it had some scuff and torn pretty much the second time I used it. I cut off the torn part and had been using the remainder of it for the past three/ four weeks. It has developed some holes around the rim of the bell so I will need replacement soon. Do you have suggestions?
Click to expand...
I've been there a million times. Mos sells many sleeves, higher quality, or get cheaper ones anywhere, ebay, sometimes they last long, sometimes they don't. I don't use many sleeves at all, except using under my Corona ridge to beat water buildup and superficial expansion.
 
You must log in or register to reply here.
Help Users

You haven't joined any rooms.

    You haven't joined any rooms.
    Back
    Top