- Joined
- Jan 6, 2023
- Messages
- 11,016
You don't use the vacu vin cork?
Bathmate mod
- Thread starter Bassman44
- Start date
- Joined
- Mar 9, 2013
- Messages
- 69
no never needed to use it
- Joined
- Jan 6, 2023
- Messages
- 11,016
Okey.
- Joined
- Jan 6, 2023
- Messages
- 11,016
@Bassman44 look at this.
is that just for convenience? Keeping the cork attached? I wanted to secure mine into a 1” Inside diameter tubing and press it against the valve instead of going over top of the valve of the hydromax just in case I can’t release the pressure. 🤷♂️
- Joined
- Jan 6, 2023
- Messages
- 11,016
Follow the link:
Bathmate mod
Hey y’all, could someone direct me to the wine vac mod for the Hydro max? Or whatever vacuum mod you recommend ? I am maxing out my pressure of my hydromax and would like a little more pull from the vacuum
mattersofsize.com
- Joined
- Jan 6, 2023
- Messages
- 11,016
To use a Phallosan forte sleeve for this mod didn't work so well. You need a flexible tube that's also hard, otherwise you will have problem to draw vaccum. 😂🤣😆
- Joined
- Jan 6, 2023
- Messages
- 11,016
- Joined
- Jan 6, 2023
- Messages
- 11,016
Try it! I have always thought about that.
- Joined
- Aug 21, 2021
- Messages
- 244
What's your routine ?
5x5x3 Upped it to 8x4x3 and I’m getting way better expansion had to take some time off of the ssj due to cock not staying hard enough. I can work for about 4 minutes lol
- Joined
- Jun 3, 2003
- Messages
- 124,499
Awesome! You are going to see incredible results
- Joined
- Jan 6, 2023
- Messages
- 11,016
The VaccuVin mod works.
How to:
1. Remove the replacement valve carefully with this tool:
2. Then you have this: Top part of the pump.
It's now a hole right through.
3. Tape with Gorilla tape and electrical tape, to make it so, that you can't compress the spring.
4. Put the cork for the VaccuVin pump in place instead of the Bathmate valve.
4. Tape with electrical tape and self-vulcanising tape/self-fusing tape, to make it vaccum tight and water tight.
That's it. Now you can go beyond the original max vaccum/pressure. Be careful.
Here is how it looks like:
I don't know how long the cork are going to last, so in the future you can put a pvc tube, or maybe pipe between the Bathmate and the cork. In that way it's easy to replace the cork.
Hope this helps.
How to:
1. Remove the replacement valve carefully with this tool:
2. Then you have this: Top part of the pump.
It's now a hole right through.
3. Tape with Gorilla tape and electrical tape, to make it so, that you can't compress the spring.
4. Put the cork for the VaccuVin pump in place instead of the Bathmate valve.
4. Tape with electrical tape and self-vulcanising tape/self-fusing tape, to make it vaccum tight and water tight.
That's it. Now you can go beyond the original max vaccum/pressure. Be careful.
Here is how it looks like:
I don't know how long the cork are going to last, so in the future you can put a pvc tube, or maybe pipe between the Bathmate and the cork. In that way it's easy to replace the cork.
Hope this helps.
- Joined
- Jan 6, 2023
- Messages
- 11,016
- Joined
- Dec 19, 2015
- Messages
- 5,925
you can also keep the BM 'as-is' and just slide a short piece of PVC to act as a connection point for the VV pump...no need to dismantle anything and no need to use the VV cork
- Joined
- Jan 6, 2023
- Messages
- 11,016
Okey. But how do you release the vaccum after pumping, if all that is semi-permanently attached?
- Joined
- Dec 19, 2015
- Messages
- 5,925
The BM valve is spring-loaded so I just press-down to relieve any/all pressure
- Joined
- Jan 6, 2023
- Messages
- 11,016
okey so you remove the pvc tubing to release the pressure/vaccum?
Similar threads
- Sticky
Equipment modification
Modification to Bathmate HydroXtreme 7 with a pressure gauge
