squirt_inducer_man
(SIM)
You don't use the vacu vin cork?
Bathmate mod
- Thread starter Bassman44
- Start date
no never needed to use it
squirt_inducer_man
(SIM)
Okey.
squirt_inducer_man
(SIM)
@Bassman44 look at this.
is that just for convenience? Keeping the cork attached? I wanted to secure mine into a 1” Inside diameter tubing and press it against the valve instead of going over top of the valve of the hydromax just in case I can’t release the pressure.
squirt_inducer_man
(SIM)
Follow the link:is that just for convenience? Keeping the cork attached? I wanted to secure mine into a 1” Inside diameter tubing and press it against the valve instead of going over top of the valve of the hydromax just in case I can’t release the pressure.
squirt_inducer_man
(SIM)
To use a Phallosan forte sleeve for this mod didn't work so well. You need a flexible tube that's also hard, otherwise you will have problem to draw vaccum. 
squirt_inducer_man
(SIM)
squirt_inducer_man
(SIM)
Try it! I have always thought about that.is that just for convenience? Keeping the cork attached? I wanted to secure mine into a 1” Inside diameter tubing and press it against the valve instead of going over top of the valve of the hydromax just in case I can’t release the pressure.
derekparle
New member
What's your routine ?
5x5x3 Upped it to 8x4x3 and I’m getting way better expansion had to take some time off of the ssj due to cock not staying hard enough. I can work for about 4 minutes lol
Awesome! You are going to see incredible results
squirt_inducer_man
(SIM)
The VaccuVin mod works.
How to:
1. Remove the replacement valve carefully with this tool:
View attachment 1832991
2. Then you have this: Top part of the pump.
View attachment 1832992
It's now a hole right through.
3. Tape with Gorilla tape and electrical tape, to make it so, that you can't compress the spring.
4. Put the cork for the VaccuVin pump in place instead of the Bathmate valve.
4. Tape with electrical tape and self-vulcanising tape/self-fusing tape, to make it vaccum tight and water tight.
That's it. Now you can go beyond the original max vaccum/pressure. Be careful.
Here is how it looks like:
View attachment 1832990
I don't know how long the cork are going to last, so in the future you can put a pvc tube, or maybe pipe between the Bathmate and the cork. In that way it's easy to replace the cork.
Hope this helps.
How to:
1. Remove the replacement valve carefully with this tool:
View attachment 1832991
2. Then you have this: Top part of the pump.
View attachment 1832992
It's now a hole right through.
3. Tape with Gorilla tape and electrical tape, to make it so, that you can't compress the spring.
4. Put the cork for the VaccuVin pump in place instead of the Bathmate valve.
4. Tape with electrical tape and self-vulcanising tape/self-fusing tape, to make it vaccum tight and water tight.
That's it. Now you can go beyond the original max vaccum/pressure. Be careful.
Here is how it looks like:
View attachment 1832990
I don't know how long the cork are going to last, so in the future you can put a pvc tube, or maybe pipe between the Bathmate and the cork. In that way it's easy to replace the cork.
Hope this helps.
Attachments
squirt_inducer_man
(SIM)
Big Schwanz Acht
@Big Schwanz Acht
you can also keep the BM 'as-is' and just slide a short piece of PVC to act as a connection point for the VV pump...no need to dismantle anything and no need to use the VV cork
squirt_inducer_man
(SIM)
Okey. But how do you release the vaccum after pumping, if all that is semi-permanently attached?
Big Schwanz Acht
@Big Schwanz Acht
The BM valve is spring-loaded so I just press-down to relieve any/all pressure
squirt_inducer_man
(SIM)
okey so you remove the pvc tubing to release the pressure/vaccum?