Progress thread SIM's penis enlargement journey

Status
Not open for further replies.
oldandlively said:
No worries brother. I'm working side by side with you on this project. I'm waiting on one more part that supposedly coming within this week. It worried me that the container imploded early, even with a 2 to 2.5mm thickness. I went ahead and purchases a 2 to 2.2mm thick 64oz water container with a moderate size mouth to test. I believe I also found a 1000mL size (~33oz) on AliExpress designed to handle chemical type liquids, with thick walls. I will do step by step instruction and testing phases for MOS to mirror, leading to production or DIY for brothers that like to take this project for the fun of it.
Click to expand...
Sounds good. I have some ideas.
 
oldandlively said:
You're making me wonder if I need to revisit my calculations. I have so many free containers at the ready after doing preliminary pressure testingw, and now I second guess myself. I have thin wall from 1.5mm to thick ones at 3mm. All sustained 20inHg vacuum for continuous 20 minutes. I may have to increase it to 2 hours instead.
Click to expand...
Do you test these containers with warm water at different levels and vaccum pressure?

I believe the best way to test a water trap is to use it in your routine, and use that one way valve between the penis cylinder and water trap for security/protection.

I'm pretty fast to pump up to 10 in.Hg vaccum pressure.
 
squirt_inducer_man said:
Do you test these containers with warm water at different levels and vaccum pressure?

I believe the best way to test a water trap is to use it in your routine, and use that one way valve between the penis cylinder and water trap for security/protection.

I'm pretty fast to pump up to 10 in.Hg vaccum pressure.
Click to expand...
Yes. I use water temps just above the normal bath water, just above 105F (40C). After your implosion, rather than just pumping the pressure and allow to remain static for a few minutes, I'll be stressing them all for at least 5 hours under pressure. Then bleed the air and resume again. All containers will be under pressure for a few days straight.
 
oldandlively said:
Yes. I use water temps just above the normal bath water, just above 105F (40C). After your implosion, rather than just pumping the pressure and allow to remain static for a few minutes, I'll be stressing them all for at least 5 hours under pressure. Then bleed the air and resume again. All containers will be under pressure for a few days straight.
Click to expand...
Sounds good.
 
The bigger the container is the harder it will be to increase the vaccum with a small hand vaccum pump.

So far the protein shaker have been the best for me The new protein shaker (did just replace the container and not the lid) are holding up so far.

I will try out this contraption now.
I do not have a protection valve but it can with ease hold well beyond 15 in.Hg so I will be safe.
 
I keep having the wrong dimensions on the tubing, but I could put this togheter with parts from the MityVac system and the parts that was included with this water trap.
 
Just longer hoses/tubing and this will probably be a very comfortable setup. Just having it on the floor in the shower instead on the toilet seat.




I will do my testing now.
 
Refer to:
Post in thread 'SIM's penis enlargement journey' https://mattersofsize.com/threads/sims-penis-enlargement-journey.1830265/post-1966624

The system was not completely vaccum tight, I believe it was due to the fittings in the lid. They where only screwed in the plastic with a rubber gasket under them. No nut on the underside to secure them. No gasket in the lid either but I do not have that on my other water trap, and that trap is 100% vaccum tight until implosion.
 
The pursuit of a bigger penis.

squirt_inducer_man said:
The system was not completely vaccum tight, I believe it was due to the fittings in the lid. They where only screwed in the plastic with a rubber gasket under them. No nut on the underside to secure them. No gasket in the lid either but I do not have that on my other water trap, and that trap is 100% vaccum tight until implosion.
Click to expand...
Hm. How about adding the hot glue for now until you can obtain the locking nuts for the underside?
 
oldandlively said:
The pursuit of a bigger penis.


Hm. How about adding the hot glue for now until you can obtain the locking nuts for the underside?
Click to expand...
Yes that would be a solution, but there is not really any room for a nut.

I don't know if this container is the "one".
If I could get hold of a lid without any pre-drilled holes, maybe this container will work.

Just drilling the holes a little bit more to the middle (not much, would help).

See attachments, extremely tight.
For now my protein shaker have been the best. But can't use that now because I stole a fitting from that to this one. 🤔

If I wouldn't care about trying to prefect a water trap I would be happy with my hot glued protein shaker.
 
squirt_inducer_man said:
I just wanted to login and share my progress.

I'm starting to get uncomfortable sharing pictures of my penis, but I thought them would help if someone else are dealing with this upward curve and pumping situation.

I'm working on figuring out a comersial solution for a bigger water trap (MityVac Hydro-Vac Penis Pump) for @DLD and this brotherhood. You need a bigger water trap to make pumping efficient.

But it will take some time. I ordered the wrong parts, but it was hard to picture what I needed when I didn't had anything. Need to make sure the measurements work with the MityVac cylinders and vaccum pump handle. I even ordered the wrong tubing. I do not promise anything, but I do will do my best.

There will be some time until I can give an update on this.
Take care, and thank you all for everything.
Click to expand...
Thanks for your bravery. You are dedicated to the brotherhood
 
oldandlively said:
No worries brother. I'm working side by side with you on this project. I'm waiting on one more part that supposedly coming within this week. It worried me that the container imploded early, even with a 2 to 2.5mm thickness. I went ahead and purchases a 2 to 2.2mm thick 64oz water container with a moderate size mouth to test. I believe I also found a 1000mL size (~33oz) on AliExpress designed to handle chemical type liquids, with thick walls. I will do step by step instruction and testing phases for MOS to mirror, leading to production or DIY for brothers that like to take this project for the fun of it.
Click to expand...
@DLD don't forget @oldandlively, he's doing alot of work as well.
 
Status
Not open for further replies.
Back
Top