Mytivac cylinder

S

sjpmsd2018

Member
Registered
Joined
Oct 31, 2019
Messages
4
Hi received mytivac cylinder today and with a base silicone cushion. The entry hole for the silicone very small....how to do pumping with use of the silicone sleeve base...please guide. Thanks
 
You don't need the silicone sleeve when pumping. Enter the pump erect and pump at 5hg if you are new to pumping. The base of the mityvac is friendly.
 
Hi thanks for the reply....I am doing pumping since 2 years now. What is the purpose of the mytivac seal they send me...I am 5.3 girth..how to go inside the cylinder through the seal with small hole....please advise
 
I don't know what seal you are talking about. Is the pump too small?
 
I mean the mytivac pump seal silicone ...which is attaching to the base of the cylinder while pumping as a cushion.
 
sjpmsd2018 said:
I mean the mytivac pump seal silicone ...which is attaching to the base of the cylinder while pumping as a cushion.
Click to expand...

You don't need that as long as you don't feel pains when pumping with the mityvac.
 
I tried to use my new MityVac this morning without mightysleev with no luck.. Couldn't get a good seal. What's the trick? I'm using the 2.5inch tube
 
I love the MityVac I finally shaved all my pubes with a razor and the seal is tighter than ever. I didn’t have to use Vaseline I just used water based lubricant on the penis.

Trying sitting down for a tighter seal
 
Last edited:
The seal coming with the mytivac cylinder is very useful in pumping, it will stop the part of the scrotum going in to the cylinder. When I got it, I got doubt how the 5'' penis can go inside as the hole of the slicone cusion is very small. But I found the idea to get in easly. Put some KY jelley on the hole of the silicon seal cushion and little on the glans ---- then press the tip of the glans against the hole and slowly pump. You can see the penis will slide easly and get in to the cylinder. Hope it helps
 
sjpmsd2018 said:
The seal coming with the mytivac cylinder is very useful in pumping, it will stop the part of the scrotum going in to the cylinder. When I got it, I got doubt how the 5'' penis can go inside as the hole of the slicone cusion is very small. But I found the idea to get in easly. Put some KY jelley on the hole of the silicon seal cushion and little on the glans ---- then press the tip of the glans against the hole and slowly pump. You can see the penis will slide easly and get in to the cylinder. Hope it helps
Click to expand...

On the MOS SHOP it is written a note about the, MITYSLEEV, or you can say a warning ⚠️.

Note: If the seal is too tight for your girth, apply the MitySleev to a pipe that is as thick or slightly thicker than your girth and let sit for 24 hours. If you don't follow this procedure, you may risk ripping the sleeve from use.
Click to expand...

It looks like the seal can rip, if you do not adjust the hole for your penis.
 
You must log in or register to reply here.

Similar threads

H
Mytivac vs Bathmate
Replies
0
Views
325
H
hoppyj01
H
B
Silicone sleeve/comfort ring on the Mityvac
Replies
5
Views
757
T
tryn4more
T
P
Should i size up?
Replies
17
Views
652
DLD
DLD
DLD
O
How to remove cylinder head for maintenance?
Replies
4
Views
202
squirt_inducer_man
squirt_inducer_man
squirt_inducer_man
P
Soreness
Replies
17
Views
943
squirt_inducer_man
squirt_inducer_man
squirt_inducer_man
Back
Top Bottom