shrinkage or poor EQ?

[Hung-Honcho]

I did my BPEL measurement about 2weeks ago and I was at 8.2 - 8.3 inches and my flaccid was around 7.8. I did some stretching using the length master hooked to a weight support (a little bit similar to @TuffDong set up) so I don't have to stress my hands and after that I did some btc, did this for about a week and then yesterday I took my measurement, my BPFSL was 8 inches but my BPEL was 7.8 inches!!! wtf is going on here? can anyway make sense out of this?

 

[49-er]

I'd say prob more around the EQ than shrinkage personally

 

[DLD]

It could be because of fatigue and a number of other reasons. Don’t second-guess a lower measurement when you have a higher measurement prior. This usually only happens when you have poor eq. To avoid this you can always measure flaccid stretched bone pressed, This measurement will always be consistent as long as you measure against the bone in the same place every time.

 

[Hung-Honcho]

It could be because of fatigue and a number of other reasons. Don’t second-guess a lower measurement when you have a higher measurement prior. This usually only happens when you have poor eq. To avoid this you can always measure flaccid stretched bone pressed, This measurement will always be consistent as long as you measure against the bone in the same place every time.

My bone pressed flaccid length has been on 8 or 8.1 inches for a few weeks now so I am guessing its an EQ issue as you suggested.

 

[Straight28]

I didn't know it was possible to have a longer erection than flaccid stretch.. How are you measuring? For instance, my BPFSL 8.5 is an entire inch more than my BPEL 7.5. That makes me think your EQ would be through the roof..

 

[Hung-Honcho]

I didn't know it was possible to have a longer erection than flaccid stretch.. How are you measuring? For instance, my BPFSL 8.5 is an entire inch more than my BPEL 7.5. That makes me think your EQ would be through the roof..

I push the ruler on the fat pad and take my measurement from there. I have stepped up my PE workouts this month after stopping for 5 months so I guess the fatigue on my penis might be affecting my EQ.

 

[DLD]

Length measurements should always be done at the center of the pubic bone firmly pressed against the bone and measured to the tip of the head. If erections are difficult when trying to get a measurement simply go with a flaccid-stretched, bone-pressed measurement, this will always show your true gains.

 

[Getbiglonger7]

Most of the time we expect gains simply by placing the ruler on the base of the penis to the tip of our cocks, sometimes the results are dissapointing, D is right when he says that measuring bpfsl is the rule..

 

[DLD]

Most of the time we expect gains simply by placing the ruler on the base of the penis to the tip of our cocks, sometimes the results are dissapointing, D is right when he says that measuring bpfsl is the rule..

It really has to be the rule because there’s such fluctuation when it comes to having an erection. Take that all out of the equation and just measure flaccid-stretched, bone-pressed.

 

[Hung-Honcho]

It really has to be the rule because there’s such fluctuation when it comes to having an erection. Take that all out of the equation and just measure flaccid-stretched, bone-pressed.

How do you calculate your actual bone pressed erect length by measuring your BPFSL?

 

[DLD]

How do you calculate your actual bone pressed erect length by measuring your BPFSL?

I don’t understand the question. Do you mean is there a difference between the two? Please rephrase this my brother and I will answer you

 

[Hung-Honcho]

I don’t understand the question. Do you mean is there a difference between the two? Please rephrase this my brother and I will answer you

In your post above you wrote "Take that all out of the equation and just measure flaccid-stretched, bone-pressed. " so I am asking is there a way to get an estimate of your BPEL measurement from your BPFSL measurement? correct me if I am wrong but your post above seems to suggest that the flaccid stretched measurement could be used to get an estimate of the BPEL.

 

[DLD]

In your post above you wrote "Take that all out of the equation and just measure flaccid-stretched, bone-pressed. " so I am asking is there a way to get an estimate of your BPEL measurement from your BPFSL measurement? correct me if I am wrong but your post above seems to suggest that the flaccid stretched measurement could be used to get an estimate of the BPEL.

There will always be a difference between the two approximately a half inch. So even as you get bigger you’ll always be behind by a quarter to a half of an inch.

 

[huge-girth]

I did my BPEL measurement about 2weeks ago and I was at 8.2 - 8.3 inches and my flaccid was around 7.8. I did some stretching using the length master hooked to a weight support (a little bit similar to @TuffDong set up) so I don't have to stress my hands and after that I did some btc, did this for about a week and then yesterday I took my measurement, my BPFSL was 8 inches but my BPEL was 7.8 inches!!! wtf is going on here? can anyway make sense out of this?

This is 2 years and 4 months since you made this post. I wonder if you ever got to 9 inches bone press. I'm 8.2 myself and hoping to be 9 inches.

 

[DLD]

This is 2 years and 4 months since you made this post. I wonder if you ever got to 9 inches bone press. I'm 8.2 myself and hoping to be 9 inches.

It would be awesome if everyone stuck to it....the growth would be insane