Mytivac cylinder

[sjpmsd2018]

Hi received mytivac cylinder today and with a base silicone cushion. The entry hole for the silicone very small....how to do pumping with use of the silicone sleeve base...please guide. Thanks

 

[huge-girth]

You don't need the silicone sleeve when pumping. Enter the pump erect and pump at 5hg if you are new to pumping. The base of the mityvac is friendly.

 

[sjpmsd2018]

Hi thanks for the reply....I am doing pumping since 2 years now. What is the purpose of the mytivac seal they send me...I am 5.3 girth..how to go inside the cylinder through the seal with small hole....please advise

 

[huge-girth]

I don't know what seal you are talking about. Is the pump too small?

 

[sjpmsd2018]

I mean the mytivac pump seal silicone ...which is attaching to the base of the cylinder while pumping as a cushion.

 

[huge-girth]

I mean the mytivac pump seal silicone ...which is attaching to the base of the cylinder while pumping as a cushion.

You don't need that as long as you don't feel pains when pumping with the mityvac.

 

[BFL]

I tried to use my new Mightyvac this morning without mightysleev with no luck.. Couldn't get a good seal. What's the trick? I'm using the 2.5inch tube

 

[huge-girth]

I tried to use my new Mightyvac this morning without mightysleev with no luck.. Couldn't get a good seal. What's the trick? I'm using the 2.5inch tube

Use some Vaseline on the part of the pump that presses against your pubic area. Also shave completely if possible.

 

[DLD]

Use some Vaseline on the part of the pump that presses against your pubic area. Also shave completely if possible.

Vaseline is a seals best friend

 

[orgasmic19]

I love the MityVac I finally shaved all my pubes with a razor and the seal is tighter than ever. I didn’t have to use Vaseline I just used water based lubricant on the penis.

Trying sitting down for a tighter seal

 

[DLD]

I love the MityVac I finally shaved all my pubes with a razor and the seal is tighter than ever. I didn’t have to use Vaseline I just used water based lubricant on the penis.

Trying sitting down for a tighter seal

Such good news

 

[sjpmsd2018]

The seal coming with the mytivac cylinder is very useful in pumping, it will stop the part of the scrotum going in to the cylinder. When I got it, I got doubt how the 5'' penis can go inside as the hole of the slicone cusion is very small. But I found the idea to get in easly. Put some KY jelley on the hole of the silicon seal cushion and little on the glans ---- then press the tip of the glans against the hole and slowly pump. You can see the penis will slide easly and get in to the cylinder. Hope it helps

 

[squirt_inducer_man]

The seal coming with the mytivac cylinder is very useful in pumping, it will stop the part of the scrotum going in to the cylinder. When I got it, I got doubt how the 5'' penis can go inside as the hole of the slicone cusion is very small. But I found the idea to get in easly. Put some KY jelley on the hole of the silicon seal cushion and little on the glans ---- then press the tip of the glans against the hole and slowly pump. You can see the penis will slide easly and get in to the cylinder. Hope it helps

On the MOS SHOP it is written a note about the, MITYSLEEV, or you can say a warning .

Note: If the seal is too tight for your girth, apply the MitySleev to a pipe that is as thick or slightly thicker than your girth and let sit for 24 hours. If you don't follow this procedure, you may risk ripping the sleeve from use.

It looks like the seal can rip, if you do not adjust the hole for your penis.

 

[DLD]

Always pre stretch you sleeves over a bottle if you need more room. Also use a bit of baby powder to help them slide on easier