Large vein causes issues with the Mityvac

[msax999]

Hi,

I have a 2 x 9.25 cylinder. It works well for me. I'm focusing on length, not girth --- and maxing out the 2" cylinder or a little more is ideal for me.

The problem I have is that I have a large vein running along my cock near the base and about 2-3 inches up the shaft. When I pump, the vein forms a kind of "air seal" where air gets trapped between the vein and my cock. Instead of that area expanding to the full cylinder width, it actually compresses and results in that one area on one side being less girthy than everywhere else.

I'm also thicker near the head than the base --- I have the make sure my head is lubed well to get it in the cylinder. The lower half get the most girth benefits from the pumping. Makes it annoying that the base is getting distorted by the vein issue.

Any suggestions? I'm close to maxing out the 2". Would going up a size make sense? Should I try a condom or silicone sleeve to even it out?

Thanks.

 

[DLD]

As much as you may want to stick with that tube I think you will need one slightly wider or the vein will continue to be a problem

 

[derekparle]

Has anyone found a cheap 1.5-1.65" cylinder in Europe?

 

[GashKing]

Has anyone found a cheap 1.5-1.65" cylinder in Europe?

Check out eBay?

 

[GashKing]

Hi,

I have a 2 x 9.25 cylinder. It works well for me. I'm focusing on length, not girth --- and maxing out the 2" cylinder or a little more is ideal for me.

The problem I have is that I have a large vein running along my cock near the base and about 2-3 inches up the shaft. When I pump, the vein forms a kind of "air seal" where air gets trapped between the vein and my cock. Instead of that area expanding to the full cylinder width, it actually compresses and results in that one area on one side being less girthy than everywhere else.

I'm also thicker near the head than the base --- I have the make sure my head is lubed well to get it in the cylinder. The lower half get the most girth benefits from the pumping. Makes it annoying that the base is getting distorted by the vein issue.

Any suggestions? I'm close to maxing out the 2". Would going up a size make sense? Should I try a condom or silicone sleeve to even it out?

Thanks.

Try the silicone sleeve; i use one during and after pumping to minimize fluid build up, give it a shot and keep us apprised - post some pics, good luck Brother

Happy PE'ing

 

[GashKing]

Hi,

I have a 2 x 9.25 cylinder. It works well for me. I'm focusing on length, not girth --- and maxing out the 2" cylinder or a little more is ideal for me.

The problem I have is that I have a large vein running along my cock near the base and about 2-3 inches up the shaft. When I pump, the vein forms a kind of "air seal" where air gets trapped between the vein and my cock. Instead of that area expanding to the full cylinder width, it actually compresses and results in that one area on one side being less girthy than everywhere else.

I'm also thicker near the head than the base --- I have the make sure my head is lubed well to get it in the cylinder. The lower half get the most girth benefits from the pumping. Makes it annoying that the base is getting distorted by the vein issue.

Any suggestions? I'm close to maxing out the 2". Would going up a size make sense? Should I try a condom or silicone sleeve to even it out?

Thanks.

This one may also help you?

https://www.ebay.com/itm/1837626275...lYP5no-Sym&var=&widget_ver=artemis&media=COPY

https://www.ebay.com/itm/1837626275...lYP5no-Sym&var=&widget_ver=artemis&media=COPY

 

[GashKing]

Hi,

I have a 2 x 9.25 cylinder. It works well for me. I'm focusing on length, not girth --- and maxing out the 2" cylinder or a little more is ideal for me.

The problem I have is that I have a large vein running along my cock near the base and about 2-3 inches up the shaft. When I pump, the vein forms a kind of "air seal" where air gets trapped between the vein and my cock. Instead of that area expanding to the full cylinder width, it actually compresses and results in that one area on one side being less girthy than everywhere else.

I'm also thicker near the head than the base --- I have the make sure my head is lubed well to get it in the cylinder. The lower half get the most girth benefits from the pumping. Makes it annoying that the base is getting distorted by the vein issue.

Any suggestions? I'm close to maxing out the 2". Would going up a size make sense? Should I try a condom or silicone sleeve to even it out?

Thanks.

Like DLD said, i would bump up to a next size up 2.5"

https://www.ebay.com/itm/2016182111...ar=500853981260&widget_ver=artemis&media=COPY