Is anyone else having issues with Penimaster Pro Vacuum chamber?

A

Avengere

Member
I have penimaster vacuum cap.

I used it regularly and it worked fine (with no split adapters). My glans were held in place.

Then I took a break for a month or so.

Now I want to start using it again, but my penis glans ALWAYS slide out. I can't understand why. Maybe because I have foreskin, but it was fine before.

I put in large split adapter and head did not go through. I put on medium split adapter and head went through to the chamber, but STILL was pushed out.

I just can't understand what is wrong. I replaced the rubber, but still getting the same problem.

The glans just go out of chamber at all times, even when using split adapters.

How is that even possible? It seems like genuine mystery.
 
Avengere said:
I have penimaster vacuum cap.

I used it regularly and it worked fine (with no split adapters). My glans were held in place.

Then I took a break for a month or so.

Now I want to start using it again, but my penis glans ALWAYS slide out. I can't understand why. Maybe because I have foreskin, but it was fine before.

I put in large split adapter and head did not go through. I put on medium split adapter and head went through to the chamber, but STILL was pushed out.

I just can't understand what is wrong. I replaced the rubber, but still getting the same problem.

The glans just go out of chamber at all times, even when using split adapters.

How is that even possible? It seems like genuine mystery.
Click to expand...
By any chance you figure it out? I took a little over a week off and when I went back I disassembled and put it back together but unfortunately its just not the same. Mine came with both split adapters but I did not bother with them my first go 'round. Worked fine up until about week ago(Still very new to enhancement). I am still waiting for that eureka moment but as of now my main tool is out of commission. If you could walk me through on what/how you did what you did to get using again? Thank you much appreciated.
 
Frankly Mr.Shankly said:
By any chance you figure it out? I took a little over a week off and when I went back I disassembled and put it back together but unfortunately its just not the same. Mine came with both split adapters but I did not bother with them my first go 'round. Worked fine up until about week ago(Still very new to enhancement). I am still waiting for that eureka moment but as of now my main tool is out of commission. If you could walk me through on what/how you did what you did to get using again? Thank you much appreciated.
Click to expand...

The Penimaster Pro was the one piece of equipment I regret buying. Too finicky to get right and one of the spring bars broke after 2 months with non-existent customer service.
Couple tips to get the glans chamber to stay:
- use a tiny bit of water-based lube instead of their glorified Vaseline. I found this held better. Also, their product degrades the diaphragms rather quickly.
- try going into the chamber semi erect (maybe 30-50%)
- try 2 bulb pumps worth of suction. After going in with one pump, close the valve, depress the bulb again, open valve, and allow glans to go in further
- when glans is in, before closing the valve, give the bulb a few micropumps to seat the glans effectively
- if glans is still slipping, you probably need a smaller sleuce and/or diaphragm
Good luck.
 
I highly recommend people stick with brotherhood equipment as we have put so much work into this to give you the highest quality for the lowest possible price. Check out the StealthStretcher, It is a combination of every ADS out there. If not only comes with a vacuum system it also comes with a rod system. I highly recommend this as the only extender men need to acquire. I can write incredible routines when I have this device to work with.
 
I used to use this device. But I kept slipping out because I think that air was getting inside somehow. Also my glans was simply too large for the device. The last time I used it, I as when I decided to get the silistretcher.
 
  • Like
Reactions: DLD
Rollie_Boy said:
There is no comparison ?. Silistretcher is the clear winner in my book
Click to expand...

and that comparison is between every single ADS on the market. It doesn’t matter which extender you choose the best extender will always be the SiliStretcher and the StealthStretcher. Men can truly put on length by exclusively using the SS. But when you combine the SS with one of my SRT workouts, it’s to the moon baby!
 
Avengere said:
I have penimaster vacuum cap.

I used it regularly and it worked fine (with no split adapters). My glans were held in place.

Then I took a break for a month or so.

Now I want to start using it again, but my penis glans ALWAYS slide out. I can't understand why. Maybe because I have foreskin, but it was fine before.

I put in large split adapter and head did not go through. I put on medium split adapter and head went through to the chamber, but STILL was pushed out.

I just can't understand what is wrong. I replaced the rubber, but still getting the same problem

The glans just go out of chamber at all times, even when using split adapters.

How is that even possible? It seems like genuine mystery.
Click to expand...
 
I had similar problem it was because I had over tightened the screw on top of the chamber which had ceased to do it's job correctly. I replaced it and cautious now not to turn it hard tight and no problems.
 
  • Like
Reactions: DLD
You must log in or register to reply here.
Back
Top