ADS/Sleeves for smaller flaccid girth

[arthurbrown918]

Hello, been doing PE on and off for a while, recently decided to be consistent with length work, esp ADS.

I'm not in NA so limited options, but managed to find some knockoff size genetics locally (SEA).

I've got two version of the SG, the first one only had holes under where the glans goes, secured by a long rubber/plastic/silicone tube that I usually position just under the glans. The second version has an additional strap that inserts into the plastic along the shaft.

I found the first method quite troublesome, needed to tighten the tube so much that I started to be concerned about blood loss to the head. Could only use for 1.5hrs at a time, at the end of which the head of my penis was cold to the touch (ambient 30+C/~90F so its not the cold). Also very painful.

The second method however, does not secure my penis in place at all. There's a foam sleeve included in the pack, but that doesnt help. Either way, tugging with even a little force causes my penis to slip out. Measured my flaccid girth and its about 3" in circumference, so less than 1" in diameter. The space left by the strap (fully tightened) is around the same (3" in circumference). I suspect there's a requirement similar to condom sizing (<90% of EG so it stays on) involved here.

Wondering if other members have had a problem like this, what solutions they tried, and what I could try.

Somewhat related would be questions about sizing a sleeve: Is the width measured the same way a condom is measured, laid flat on a ruler? I was able to buy some silicone sleeves advertised for penis enlargement but it seems like theyre too big becasue they dont prevent my penis from turtling at all.

 

[DLD]

Hello, been doing PE on and off for a while, recently decided to be consistent with length work, esp ADS.

I'm not in NA so limited options, but managed to find some knockoff size genetics locally (SEA).

I've got two version of the SG, the first one only had holes under where the glans goes, secured by a long rubber/plastic/silicone tube that I usually position just under the glans. The second version has an additional strap that inserts into the plastic along the shaft.

I found the first method quite troublesome, needed to tighten the tube so much that I started to be concerned about blood loss to the head. Could only use for 1.5hrs at a time, at the end of which the head of my penis was cold to the touch (ambient 30+C/~90F so its not the cold). Also very painful.

The second method however, does not secure my penis in place at all. There's a foam sleeve included in the pack, but that doesnt help. Either way, tugging with even a little force causes my penis to slip out. Measured my flaccid girth and its about 3" in circumference, so less than 1" in diameter. The space left by the strap (fully tightened) is around the same (3" in circumference). I suspect there's a requirement similar to condom sizing (<90% of EG so it stays on) involved here.

Wondering if other members have had a problem like this, what solutions they tried, and what I could try.

Somewhat related would be questions about sizing a sleeve: Is the width measured the same way a condom is measured, laid flat on a ruler? I was able to buy some silicone sleeves advertised for penis enlargement but it seems like theyre too big becasue they dont prevent my penis from turtling at all.

Go for the Silisleeve 1 for smallest size. As far as attaching the extender; try using a strip of velcro. This seems to be the best option for sizegen type extenders.

 

[huge-girth]

Hello, been doing PE on and off for a while, recently decided to be consistent with length work, esp ADS.

I'm not in NA so limited options, but managed to find some knockoff size genetics locally (SEA).

I've got two version of the SG, the first one only had holes under where the glans goes, secured by a long rubber/plastic/silicone tube that I usually position just under the glans. The second version has an additional strap that inserts into the plastic along the shaft.

I found the first method quite troublesome, needed to tighten the tube so much that I started to be concerned about blood loss to the head. Could only use for 1.5hrs at a time, at the end of which the head of my penis was cold to the touch (ambient 30+C/~90F so its not the cold). Also very painful.

The second method however, does not secure my penis in place at all. There's a foam sleeve included in the pack, but that doesnt help. Either way, tugging with even a little force causes my penis to slip out. Measured my flaccid girth and its about 3" in circumference, so less than 1" in diameter. The space left by the strap (fully tightened) is around the same (3" in circumference). I suspect there's a requirement similar to condom sizing (<90% of EG so it stays on) involved here.

Wondering if other members have had a problem like this, what solutions they tried, and what I could try.

Somewhat related would be questions about sizing a sleeve: Is the width measured the same way a condom is measured, laid flat on a ruler? I was able to buy some silicone sleeves advertised for penis enlargement but it seems like theyre too big becasue they dont prevent my penis from turtling at all.

I need you to know that the size genetics is too cumbersome and it's only a matter of time before you give up. You need a PE device that is addictive to use. 1 hour is enough everyday for a solid length routine. Get yourself a length master you won't regret it.

 

[DLD]

A much better extender would be the SiliStretcher. No straps or other cumbersome attachments. I agree with the lengthmaster being best but if you need an ads the SiliStretcher is best

 

[huge-girth]

A much better extender would be the SiliStretcher. No straps or other cumbersome attachments. I agree with the lengthmaster being best but if you need an ads the SiliStretcher is best

Yes that's true.

 

[VoorheesXIII]

Link to velcro mod thread:

https://mattersofsize.com/threads/s...modification-velcro-strap-by-j1l.48790/page-9

Also some pictures. Please be careful with constriction type extenders, they have a high risk factor for circulation loss past the point of contact i.e the glans, Vacuum based extenders are the next evolution & are far safer, but nonetheless, work with available resources.

The width of the velcro strap will distribute the contact force a little better but you definitely need to work on a wrap/sleeve or something to allow circulation, something with a bit of squish but will hold firm & give a buffer between the strap and your dick. Ideally, the Silisleeves will work, if you find they are still too large you can always double it over to give a snugger fit? Not to steer business away from MoS but there are plenty of products out there not designed for PE but can have use, maybe a finger/toe sleeve could do the trick?

 

[DLD]

Excellent

 

[derekparle]

In my experience sleeving size is not that important unless its too big. You can stretch them out if they are too tight but you can't make them smaller.

 

[DLD]

In my experience sleeving size is not that important unless its too big. You can stretch them out if they are too tight but you can't make them smaller.

Always best for a tight fit