SILISTRECHER2 MANUAL FOR THE DUMMIES

Lightning

@Lightning
Administrator
Super Moderator
Registered
Joined
Jun 3, 2003
Messages
4,176
Inside your SiliStretcher2 package you will find the following contents:
  • SiliStretcher2(s) of choice

  • Blue SiliPad and gel pads

  • Two DuroSleevs
  • Two SiliSleev2s
  • One SiliCap2
  • ADS (All Day Stretcher) Belt with clip
  • SiliStrap Shoulder Strap
  • Hanging arbor and spring clip
  • Weight plates (2.5lbs included)
  • Micro-porous tape (for foreskin users)
  • MOSGrip gripping powder

  • Discrete carry bag
silistretcher2-description.jpg

Know your SiliStretcher2

Setting the Piston

We designed the SiliStretcher2 so that the piston does not fully extract from the vacuum bell. You should not extract the piston any further than the half-way point inside the vacuum bell. This new feature prevents users from over vacuuming their penis and provides better grip and control to the penis by allowing the penis to insert into the SiliStretcher2 vacuum bell.

silistretcher2-piston-push.jpg
Retracting the Vacuum Piston
The piston should sit at the half way point (like in photo above) when not in use.

In the rare event that you over extract the piston and it no longer retracts when turning the vacuum knob, simply depress the piston with your finger (or preferably a small pipe) as you turn the vacuum knob until the piston retracts. This requires a little force and you may find it easier to use a small pipe or something hard so you can press the piston with leverage against a wall or table instead of your finger.

Remember to not over extract the piston to avoid this.

Starting Notes
Before using the SiliStretcher, make sure your penis shaft is free of hair, oil, cream, clean, dried and powdered with the supplied MOSGrip gripping powder. Hairs will create loss of suction with the Blue SiliSleevs and the SiliStretcher

SiliPads
The Blue Silipads are interchangeable and provide an extra level of comfort and help reduce fluid retention by contouring to the shape of your penis. When you receive you SiliStretcher, the blue contoured silicone SiliPad is pre-installed. You can start with this one and/or exchange with one of the other two jel pads provided. Each user has different preferences based on penis shape, size and method used.

SiliSleevs
We now include two SiliSleev2s for beginners along with the DuroSleevs to get accustom to vacuum stretching. The SiliSleev2 is a softer sleeve that is easier to apply and wear long term until your penis gets conditioned for the DuroSleev.
There are two different diameter DuroSleevs included. Find the size that fits you best without slippage or causing your penis to get cold after long hours of use. They are both interchangable with the SiliStretcher2.

SiliCap2
For people that are new to vacuum pumping or using a vacuum system similar to the SiliStretcher2, you may find fluid build up in the tip of your penis after excessive tension/weight or long periods of use. This is normal and can be massaged out after use of the SiliStretcher.2
The SiliCap2 helps reduce fluid retention (edema) in the head (glans) of your penis. Use both the SiliCap2 with the SiliPad in the beginning. Once your penis gets accustomed to vacuum pressure, you may find that you can eliminate the SiliCap2 and just use the SiliPads to prevent fluid retention.

duroband-1.jpgduroband-2.jpgduroband-3.jpg
DuroBand
The DuroBand is the short transparent band included with your SiliStretcher2. You apply this band as a top layer of protection over the DuroSleev and SiliStretcher around the vacuum bell flange. The DuroBand will increase the life of your SIliSleevs and DuroSleevs when used under your pants as an all day stretcher.

Using the SiliStretcher
Carefully attach the semi-transparent DuroSleev that was included inside the velvet bag with the SiliStretcher2. Make sure the thick-band end of the DuroSleev is attached above the flange the SiliStretcher bell and is straight on.

Put the Blue SiliCap on the head of your penis to prevent fluid retention, blistering, bruising and reduce sensitivity.​
Roll the DuroSleev back over the SiliStretcher2​
Put the head of your penis into the SiliStretcher2​
Unroll the DuroSleeve over the shaft of your penis​

Turn the SiliStretcher2 vacuum piston knob a half twist counter-clockwise. One half turn of the vacuum piston knob is 5 in.-Hg of vacuum. Your penis will be safely pulled and secured into the SiliStretcher2. Give the SiliStretcher2 a tug to test if you are properly secured inside the SiliStretcher2 before applying tension or weight.

Apply the DuroBand over the DuroSleev around the SiliStretcher2 vacuum bell flange for an extra layer of protection.

DO NOT OVER VACUUM
Do not use excessive vacuum to the point the SiliStretcher2 starts pulling the SiliSleev inside the SiliStretcher. This will eventually cause micro pin holes in the DuroSleevs and cause loss of vacuum.

Attach the ADS belt or hanger clip to the end of the SiliStretcher.

Adjust tension or weight and begin session.

To release vacuum, turn the SiliStretcher vacuum piston knob a twist in the opposite direction.

Maximize the life of your SiliSleevs
To maximize the life of your DuroSleeves, remove them from the SiliStretcher2 when not in use. Do not keep them rolled up for any period of time as this will likely stretch and deform them. Keep them clean, dried, powdered with MOSGrip and store in a ziplock bag away from direct sun or heat.

How long to use? How much tension? How much weight?
Start off light and slow, listen to your body. There is no rush, and from what we learned over the course of 20 years, that heavy tension/weights for short period sessions is not the way to gain penis length. You want moderate tension and weight for long periods of time. This allows your penis tissue to expand and then build collagen in the extended state.

For the first three days, start with an hour or two of use at moderate tension and let your penis get accustomed to stretching. Then gradually work up to six hours or more per day as you slowly increase tension.

More Info
For further information, videos and routines on the SiliStretcher, please visit our support forum at: SiliStretcher Vacuum Penis Stretcher Forum

Support: support@mattersofsize.com
Web: shop.mattersofsize.com
 
Last edited:
Awesome post lightning I was just gonna ask if you were going to make a separate thread. I can’t believe how far were coming with this! You make me very proud!
 
So badass! I love all the new pictures in the other thread!
 
Is there a video of someone putting on the silistrecher 2? I'm having a bit of trouble myself. Thx.
 
Ask and you shall receive


Is the video already there in the forum? If it is, I can't see/find it. Or did you mean that is the best place to ask for a video, so I should request there?

Sorry if I'm being dumb.

Thanks for your assistance
 
 
  • Like
Reactions: DLD
Not sure if this is the place for it, but I’m almost at 1,000 hours of wearing the Silistretcher!

Wow! That is crazy amount of time. How much growth have you seen over this thousand hours?
 
Last time I checked. I’ve gained about 3/4 of an inch. Putting me at 10 1/4”

? I am overjoyed and so proud of you! You have beat me and that’s a very big thing to say. Use that club with responsibility LOL keep up the good work my brother as I love watching you grow
 
Now that I’ve officially passed the 1000 hour mark today, I’ve realized that I may actually need to upgrade the silistretcher vacuum bell/chamber. I’m currently using the medium one. But I should probably go ahead and get the large one soon. Any idea how much it would be to just get a large bell by itself?

I’m gonna keep wearing this thing every single day. One: because It helps me hide my member while I’m at work and Two:.... because why not right?

EDIT:

I was actually gonna get the stealth stretcher large bell by itself. I don’t use the twist valve anymore on the silistretcher bell. It’s useless to me.

but apparently the stealth one only comes as a kit with the applicator ball and some sleeves. I only need the bell itself; not the things it comes with. I was gonna get this one so it would look more better under my shirt (I stretch upwards and to the left around my side).

Is there any way at all I can get just the bell by itself? I don’t need the sleeves and the vacuum ball thing.
 
  • Like
Reactions: DLD
Now that I’ve officially passed the 1000 hour mark today, I’ve realized that I may actually need to upgrade the silistretcher vacuum bell/chamber. I’m currently using the medium one. But I should probably go ahead and get the large one soon. Any idea how much it would be to just get a large bell by itself?

I’m gonna keep wearing this thing every single day. One: because It helps me hide my member while I’m at work and Two:.... because why not right?

EDIT:

I was actually gonna get the stealth stretcher large bell by itself. I don’t use the twist valve anymore on the silistretcher bell. It’s useless to me.

but apparently the stealth one only comes as a kit with the applicator ball and some sleeves. I only need the bell itself; not the things it comes with. I was gonna get this one so it would look more better under my shirt (I stretch upwards and to the left around my side).

Is there any way at all I can get just the bell by itself? I don’t need the sleeves and the vacuum ball thing.

Indeed you can my brother. Send an email to sales@mattersofsize.com and they will instruct you on how to get spare parts
 
I’ve asked them about getting only the bell for the stealth stretcher, but they said it’s only available as a kit (including the sleeves, adapter, and sleeves).
 
  • Like
Reactions: DLD
Back
Top Bottom