DLD

doublelongdaddy
Administrator
Super Moderator
Registered
Joined
Jun 3, 2003
Messages
124,016
Bone Pressed Erect Length
Penis length is defined as the linear distance along the dorsal side of the erect penis extending from the mons veneris to the tip of the glans. In non-medical terms, the penis length is measured in a straight line on the top side of the erect penis, from the start of your pubic bone to the tip of your penis. Penis circumference is defined as the linear distance around the widest, thickest, part of the erect penis.

1. Stimulate yourself into the erectile state.
2. Place your ruler at the pubic bone, at the base of your erect penis and measure to the tip of your glans.
3. Read the nearest quarter-inch measurement at the tip of your penis. (In the example shown, the measurement would be 4 and 3/4 (4.75) inches.)

Bone Pressed Flaccid Stretch
1. Make sure you are in a completely flaccid state.
2. Place your ruler at the pubic bone on the side of the penis
3. Stretch penis straight out
3. Read the nearest quarter-inch measurement at the tip of your penis

Non-Bone Pressed Erect Length
1. Stimulate yourself into the erectile state.
2. Place your ruler at the skin on the belly, at the base of your erect penis and measure to the tip of your glans without pushing ruler.
3. Read the nearest quarter-inch measurement at the tip of your penis.

Flaccid Length
1. Make sure you are in a completely flaccid state.
2. Place your ruler at the skin on the belly, at the base of your flaccid penis and measure to the tip of your glans without pushing ruler.
3. Read the nearest quarter-inch measurement at the tip of your penis.

Penis Erect Circumference
Penis length is not the only factor in determining penis size. The width, girth, or fatness, of a penis is also an important aspect when considering how you compare. Most people have a penis that is either longer and thinner, or shorter and fatter. To compare how the girth of your penis compares to the population, use the instructions below to determine your penile circumference (distance around the widest part of your penis).

1. Stimulate yourself into the erectile state.
2. Place the fabric ruler or string end at the widest part of your penis and wrap it carefully around one time. Mark the spot where the string first touches itself.
3. If using string, take the marked string and lay it against the ruler. Read to the nearest quarter-inch measurement.

Penis Flaccid Circumference
1. Make sure you are in a completely flaccid state.
2. Place the fabric ruler or string end at the widest part of your penis and wrap it carefully around one time. Mark the spot where the string first touches itself.
3. If using string, take the marked string and lay it against the ruler. Read to the nearest quarter-inch measurement.
 
Also dont forget some rulers have anywere from a .1" - .25" gap before it starts to measure, so check it up because you might have alittle more dick;)
 
Also what do you guys believe that the most comfortable ruler would be? I use a plastic one that I've rounded out the corners on.

-ItsElectric
 
I always thought that girth was took at the middle of the shaft???? I am abit thicker [0.25/0.30] at the base than the middle....I will continue to measure middle as I always have but Its nice to know some measure base-wise.

I also advise to use a wooden ruler if ya can....they seem to be very nice to use...I had loadz but they got stolen and broken :(
 
Originally posted by REDZULU2003
I always thought that girth was took at the middle of the shaft???? I am abit thicker [0.25/0.30] at the base than the middle....I will continue to measure middle as I always have but Its nice to know some measure base-wise.

I also advise to use a wooden ruler if ya can....they seem to be very nice to use...I had loadz but they got stolen and broken :(

I think both measurements are important. Midshaft and Base girth will both change throughout your program.
 
We've been needing a post like this! Good job DLD! As for the girth measurement....my shaft girth has always been the same...thats' why I've always been perplexed by the guys who measure at "midshaft", I mean that "midshaft" could be wherever they want it to be right? LOL. I've even seen some guys confess they use their base girth as their girth measurement.
 
I curve to the left. If i'm measuring str8 on won't i lose a few precious inches? 7 on the str8 7.5 on the curve.
 
Yea, I have a slight upward curve & wondered if I should be allowing for this when I measure with my cloth tape measure?
 
colorado said:
Yea, I have a slight upward curve & wondered if I should be allowing for this when I measure with my cloth tape measure?

Yes, use a cloth tape if you have a curve.
 
So those people I've seen posting pic with their measurements BP'd on either side of the shaft, rather than the top, are measuring BPL incorrectly?
 
so when doing the BEL measurement, do you put your penis straight out (parrallel with the floor) and measure on top by pressing the ruller against the bone? Or just against the skin?
 
dole01 said:
so when doing the BEL measurement, do you put your penis straight out (parrallel with the floor) and measure on top by pressing the ruller against the bone? Or just against the skin?

Bone Pressed Erect is measured in the center of the penis against the pubic bone.
 
yer so if you are like the 2 fellas (and myself) that has an upward bend.. is this measured the same... ... do we attempt to straighten out our cock when measuring?..... ive always just measured with the bend still there...
 
hope2bhuge said:
pictures wud be nicefrom where to measure from :)

As long as you measure from the same place each time your gains will track accurately. I have changed my method of measuring a few times over my career (some ways made me feel better than others) but over the past year what has been important to me in NBP size only. I occasionally measure all the methods above to see if I made progress against my old stats but what seems to matter most to me is how much dick it coming out of my body:D My favorite way to measure this is to do a FSBP measurement and start the measurement where my fat pad ends to the tip of my penis.
 
is there some place i can enter all my starting information,, and keep track of it as i go through the steps?
 
Back
Top Bottom