Dagger

0
Registered
Joined
Dec 22, 2003
Messages
127
About half a year ago I invented a device which puts an insane pressure on the tunica only. I have not used it very much, but posting the method here to get some feedback on it. A problem with it for me has been that I usually lose my erection within a minute of using it and have to restimulate myself. If someone could find a way to circumvent this, I think it can become THE girth exercise.

What you need is 2 boards(aprox. 18"x2"x1") and a hinge. Connect them together with the hinge. Put your erect penis inbetween the boards, about 5 inches up. Then use a hand on each board and as you kegel, squeeze the device, alternatingly if you need some stimulation to keep it stiff longer, you can use 1 hand. This way you can get alot more force than if you squeezed on the side of your penis manually.

The 2 ends should point upwards to your head, and the squeeze should be on the sides, to maximise tunica pressure.

With this method, im sure you can rupture the tunica if you put too much pressure on it.

Also, this method is a pure tunica workout, no skin pressure like with clamping.

Here is a few pictures of the device:
 

Attachments

  • 1.jpg
    1.jpg
    38 KB · Views: 1
  • 2.jpg
    2.jpg
    39.5 KB · Views: 1
  • 3.jpg
    3.jpg
    39.1 KB · Views: 1
  • 4.jpg
    4.jpg
    39.5 KB · Views: 1
  • Squeeze.jpg
    Squeeze.jpg
    40.6 KB · Views: 1
A machine to do toilet compression squeezes? Ingenious!
 
doublelongdaddy said:
A machine to do toilet compression squeezes? Ingenious!
haha, was just to show how it works. Just check it out, easy to make. Should make your penis so hard that you can barely bend it at all.
 
no skin pressure like with clamping

If one uses a wrap, than their isnt any skin pressure.

This device looks more for working width than girth.
 
If one uses a wrap, than their isnt any skin pressure.

This device looks more for working width than girth.
I use a wrap and the layer outside my tunica is under high pressure. Bloodvessels bulging and all.

This device puts pressure on the whole tunica, both the inside and outside penis, would assume this means the tunica would expand uniformly in all directions. Your not supposed to use it on the length of the penis, just push it as close to the base as you can, with the 2 handles pointing upward and dick outward(90 degrees angle)

Why is it this thread put in "Penile Products, Reviews and Links"? It's not a product im trying to sell, it's more like something I want others to check out and see how it works out, also on improving the design. Barely anyone reads this part of the forum. Probably belongs more in "Alternative and Experimental Penis Enlargement Methods".
 
Last edited:
what if you used a clamp with this? the clamp helps me keep my erection no matter what. So you would be able to use this device longer.
 
An effect similar but weaker than this can be experienced if you take your thumb and forefinger and squeeze as hard as you can on each side of the tunica(not above and below) at the base. Then do the same with the other hand above the first hand to increase the pressure further. This can give a pretty decent pressure, but not as good as with the device, where you probably can blow it up if you put too high a pressure on it.

what if you used a clamp with this? the clamp helps me keep my erection no matter what. So you would be able to use this device longer.
Have thought about that, tried it with clamp at base and device above, but then it compounded the skinpressure since it was already filled to max. Might work though, just need some experimenting, maybe put the clamp over the device.

Also rounded off the device a bit on the edges where you put your penis, so it wont be too much stress on the tunica at a certain spot. This might be seen on the pictures.

Someone gonna try it and give some feedback?
 
Last edited:
I think this would ROCK for width, but girth I dont think it will attack the most.
Uses similer concept as the ATS rollers, except this is applied at the base and stationary, while the ATS rollers were applied against a surface and rolled back and fourth across the penis.

The possibilities with this Dagger Crocodile, are really good.....one could do quite a number of things while being squeezed in this......but I only see this as a width exercise, unless other methods are applied to make it more for girth....although I reckon it will attack girth, but only in a small degree.

Its a GREAT concept, and will really help width builders.....width is the hardest thing IMHO from experience to gain....maybe this could really help a guy out.
 
The problem with it seems to be the gap either side. There's no pressure there and I think the blood will leak out through the blood vessels there and you'll tend to lose your erection.

I find that too much downwards pressure on the base of the penis tends to open out the blood vessels/muscles at the base and loses the erection, so a solid clamping all around the penis avoids this.

I think with clamping you're primarily trying to maximise the pressure within the tunica so that it stretches out. Due to the shape of the penis this will give you girth, but hardly any length since the circumferential stress is 2x higher than the longitudinal stress in cylindrical pressure vessels (e.g. Corpus cavernosum). That's why clamping gives little if any length gains- you're not exceeding the necessary stress in the longitudinal direction.
 
I had come up with a very similiar idea in my "calling all clampers" thread but I used old vhs tapes. Now I use metal coasters that I bonded together so as to cover my full length. I think the idea of a hinge mentioned here is the flaw. With two seperate pieces it works much better, you get even contact distribution. I recommend this highly.
 
Back
Top Bottom