Recent content by Devildog0311

  1. D

    Wanted Viagra and Cialis

    Pm sent. Thanks!
  2. D

    Wanted Viagra and Cialis

    Am getting ready to order, but ran low, and they take about twelve days receive.
  3. D

    Wanted Viagra and Cialis

    Needing one or both. Lmk. Thanks!
  4. D

    Converting an X40 to hand valve or vacuvin

    That's probably the easiest mod. Good stuff. Also, if you ever start to lose pressure, and want a sealant that's perfect for this, it's Permatex Windshield and Glass Sealant (Flowable): https://www.permatex.com/products/adhesives-sealants/permatex-flowable-silicone-windshield-glass-sealer/...
  5. D

    Converting an X40 to hand valve or vacuvin

    Bengan, can see that working. The Vacuvin "fit" in mine, but it didn't hold adequate pressure. Can see where stretching the rubber would help. One thing I did notice, I used a windshield and glass sealant to get the #2 drilled rubber wine stopper in the tube so I could utilize a hand valve kit...
  6. D

    Converting an X40 to hand valve or vacuvin

    Didn't know they were here on the board. That should help alot. Will send a message. Thanks
  7. D

    Converting an X40 to hand valve or vacuvin

    Update. Wine and beer store near me has what's called a drilled #2 rubber stopper that fits good. For anyone who wants to take the entire valve assembly out, the #3 drilled rubber wine stopper is too big. Don't use epoxy! Lol! Also, I'm not a bit angry with Bathmate for their product. It's a...
  8. D

    Converting an X40 to hand valve or vacuvin

    Their website, and the contact us tab. I receive this when I send a message, yet no one ever contacts me: "Thank you for contacting Official Hydromax Pump and for using our online form. One of our dedicated support team will be in touch shortly. If you need further assistance call +44 (0)1924...
  9. D

    Converting an X40 to hand valve or vacuvin

    Almost forgot. Urologist told me no sex whatsoever. Went for a couple of weeks without, but am just now able to have normal sex again. Before that, would be out of commission for several days if I had sex, or in actuality, stroked it the wrong way, causing it to draw up, and damn... Mostly...
  10. D

    Converting an X40 to hand valve or vacuvin

    Yes, was from the edge of the BM pressing back. Basically pressing back with a hard edge, then pulling forward with vacuum is quite the bad idea. When erect, about 3/4 of the right side of me looks like a blue, veiny mess. Left side looks like perfect. Hate that. Will show new girl left side...
  11. D

    Converting an X40 to hand valve or vacuvin

    Trust me, my exact thoughts were: "I guess I could always go live on a farm somewhere; grow a full beard, no more daily showers, and Jack what's left to old Playboys..." Lol now, but not eight months ago! Oh no! Girlfriend at the time was a very hot massage therapist, and also into Tantra. PLUS...
  12. D

    Converting an X40 to hand valve or vacuvin

    Oh, forgot to mention. Got out of shower earlier, watched a video recent girl sent me, massaged Vitamin e oil, etc., got full erect, and measured. 7.8" That's a full half inch less than before. And here's the psychological gripe! The girl I'm hanging out, with had a recent fwb with a fucking...
  13. D

    Converting an X40 to hand valve or vacuvin

    The pressure and the pushing back motion caused veins to be pulled forward into the penis. Originally thought I had torn the ligament on the right side, but wasn't it. Surgery not necessary, but for months, sex was difficult due to the pain, plus had to take loads of Cialis and Viagra. Size did...
  14. D

    Converting an X40 to hand valve or vacuvin

    This thing is puzzling me. I'll get it to pressurize with the vacuvin, but the vacuvin isn't pressed into the Bathmate housing (won't hold pressure that way), it's at the end of a piece of clear rubber tubing. (glued in place, so no leaks, but is now permanent) I can either ditch the effort, and...
  15. D

    Converting an X40 to hand valve or vacuvin

    Forgot to mention, the main valve housing is also held in place by the spring. Enough steady pressure from the inside, and the entire thing will pop out of the top. Is pretty easy. Now getting pressurized, and staying that way.... Hope it works!
Back
Top Bottom